GE Multilin 469 Instruction Manual Download

Page: 291 / 338

CHAPTER 6: ACTUAL VALUES

469 MOTOR MANAGEMENT RELAY – INSTRUCTION MANUAL

6–41

PASSCODE

SETTINGS ACCESS

settings value is

Restricted

. This message also appears

anytime that settings access is permitted and the access jumper is removed.

•

THIS FEATURE NOT PROGRAMMED:

If an attempt is made to enter an actual value

message subgroup, when the settings are not configured for that feature, this
message will appear.

•

TIME ENTRY WAS NOT COMPLETE:

Since the

TIME

settings has a special format (HH/

MM/SS.S), if

ENTER

is pressed before the complete value entered, this message

appears and the new value is not stored. Another attempt will have to be made with
the complete information.

•

TIME ENTRY WAS OUT OF RANGE:

If and invalid entry is made for the time (e.g. 35

entered for hour), this message will appear.

•

TOP OF LIST:

This message will indicate when the top of subgroup has been reached.

•

TOP OF PAGE:

This message will indicate when the top of a page has been reached.

Summary of Contents for 469



















































































































































































































































































































































Search results

Summary of Contents for 469

Reviews:

Related manuals for 469

Brands by name

Popular brands

GE Multilin 469, Instruction Manual

Search results

Summary of Contents for 469

Reviews:

Related manuals for 469

Brands by name

Popular brands