manualshive.com logo in svg

GE Multilin 469, Instruction Manual

Share
Download
GE Multilin 469 Instruction Manual Download Page 170

5–28

469 MOTOR MANAGEMENT RELAY – INSTRUCTION MANUAL

CHAPTER 5: SETTINGS

Pressure Switch Alarm

PATH: SETTINGS 

ZV

 S3 DIGITAL INPUTS 

ZV

 ASSIGNABLE INPUT 1(4)

These settings apply only if the 

INPUT 1(4) FUNCTION

 is “Pressure Sw. Alarm”.

Once the pressure switch alarm function is chosen for one of the assignable digital inputs, 
the settings messages shown here will follow the assignment message. The Pressure 
Switch alarm feature may be blocked for a specified period of time from a motor start. A 
value of zero for the block time indicates that the feature is always active, when the motor 
is stopped or running. After the block delay has expired, the digital input will be monitored. 
If a closure occurs, after the specified delay, an alarm will occur.

Pressure Switch Trip

PATH: SETTINGS 

ZV

 S3 DIGITAL INPUTS 

ZV

 ASSIGNABLE INPUT 1(4)

These settings apply only if the 

INPUT 1(4) FUNCTION

 is “Pressure Switch Trip”.

Once the Pressure Switch Trip function is chosen for one of the digital inputs, the settings 
messages shown here will follow the assignment message. The Pressure Switch Trip 
feature may be blocked for a specified period of time from a motor start. A value of zero for 
the Block time indicates that the feature is always active, when the motor is stopped or 
running. After the block delay has expired, the digital input will be monitored. If a closure 
occurs, after the specified delay, a trip will occur.

„

 

ASSIGNABLE

[

INPUT 1 FUNCTION:

Pressure Sw Alarm

Range: See above

MESSAGE

BLOCK PRES. SW. 

ALARM

Range: 0 to 5000 s in steps of 1

MESSAGE

PRESSURE SWITCH

ALARM: Unlatched

Range: Latched, Unlatched

MESSAGE

ASSIGN ALARM 

RELAYS:

Range: Alarm, Alarm & Auxiliary2, 

Alarm & Auxiliary2 & Aux3, 
Alarm & Auxiliary3, Auxiliary2, 
Aux2 & Aux3, Auxiliary3

MESSAGE

PRESSURE SW. 

ALARM

Range: 0.1 to 100.0 sec., step: 0.1

MESSAGE

PRESSURE SW. 

ALARM

Range: On, Off

„

 

ASSIGNABLE

[

INPUT 1 FUNCTION:

Pressure Switch 

Range: See above

MESSAGE

BLOCK PRES. SW. 

TRIP

Range: 0 to 5000 sec.; step: 1

MESSAGE

ASSIGN TRIP 

RELAYS:

Range: Trip, Trip & Auxiliary2, Trip & 

Aux2 & Aux3, Trip & Auxiliary3

MESSAGE

PRESSURE SW. TRIP

DELAY: 5.0 s

Range: 0.1 to 100.0 s in steps of 0.1

Summary of Contents for 469



















































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands