GE Multilin 469 Instruction Manual Download Page 283

Page: 283 / 338

CHAPTER 6: ACTUAL VALUES

469 MOTOR MANAGEMENT RELAY – INSTRUCTION MANUAL

6–33

6.6

A5 Event Recorder

6.6.1

Event 01 to Event 256

PATH: ACTUAL VALUES

A5 EVENT RECORDER

EVENT 01(256)

EVENT

[

]

<Cause>

TIME OF EVENT 01:

00:00:00.0

Range: hour:minutes:seconds

MESSAGE

DATE OF EVENT 01:

Jan. 01, 1992

Range: month day, year

MESSAGE

MOTOR SPEED DUR-

ING

Range: High Speed, Low Speed. Seen if

two-speed feature is enabled.

MESSAGE

TACHOMETER DURING

EVENT01: 0 RPM

Range: 0 to 3600 RPM. Seen only if a

Digital Input is Tachometer.

MESSAGE

EVEN

Range: 0 to 100000 A

MESSAGE

MOTOR LOAD

EVENT01: 0.00 x

Range: 0.00 to 20.00 x FLA

MESSAGE

CURRENT UNBALANCE

EVENT01: 0%

Range: 0 to 100%

MESSAGE

GROUND CURRENT

EVENT01: 0.00 A

Range: 0.00 to 5000.0 A. Not seen if

Ground CT is set as None.

MESSAGE

A Diff.

Range: 0 to 5000 A. Seen only if Phase

Differential CT is set.

MESSAGE

HOTTEST STATOR

RTD:

Range: –50 to 250°C, --- (no RTD). Seen

if at least 1 RTD is set as Stator.

MESSAGE

HOTTEST BEARING

RTD:

Range: –50 to 250°C, --- (no RTD). Seen

if at least 1 RTD is Bearing.

MESSAGE

HOTTEST OTHER

RTD:

Range: –50 to 250°C, --- (no RTD). Seen

if at least 1 RTD is set as Other.

MESSAGE

AMBIENT

RTD:

Range: –50 to 250°C, --- (no RTD). Seen

if at least 1 RTD is Ambient.

MESSAGE

Vab:

Vbc:

Vca:

EVE

Range: 0 to 20000 A. Not seen if VT

Connection set as None

MESSAGE

Van:

Vbn:

Vcn:

EVE

Range: 0 to 20000 A. Seen only if VT

Connection set as Wye.

MESSAGE

SYSTEM FREQUENCY

EVENT01: 0.00 Hz

Range: 0.00, 20.00 to 120.00 Hz. Not

seen if VT Connection is None.

MESSAGE

kVA

Range: –50000 to 50000 kVA. Not seen

if VT Connection is set as None

Summary of Contents for 469



















































































































































































































































































































































Search results

Summary of Contents for 469

Reviews:

Brands by name

Popular brands

GE Multilin 469, Instruction Manual

Search results

Summary of Contents for 469

Reviews:

Brands by name

Popular brands