GE Multilin 469 Instruction Manual Download | Manualshive

Page: 243 / 338

background image

CHAPTER 5: SETTINGS

469 MOTOR MANAGEMENT RELAY – INSTRUCTION MANUAL

5–101

5.14.4 Test Output Relays

PATH: SETTINGS

ZV

S13 469 TESTING

ZV

TEST OUTPUT RELAYS

In addition to the simulation modes, the

TEST OUTPUT RELAYS

settings group may be used

during startup or testing to verify that the output relays are functioning correctly.

The output relays can only be forced to operate only if the motor is stopped and there are
no trips, alarms, or start blocks active. If any relay is forced to operate, the relay will toggle
from its normal state when there are no trips, alarms, or blocks to its active state. The
appropriate relay indicator will illuminate at that time. Selecting “Disabled” places the
output relays back in service. If the 469 measures phase current or control power is cycled,
the

FORCE OPERATION OF RELAYS

settings will automatically become disabled and the

output relays will revert back to their normal states.

If any relay is forced, the 469 In Service LED will flash, indicating that the 469 is not in
protection mode.

5.14.5 Test Analog Outputs

PATH: SETTINGS

ZV

S13 469 TESTING

ZV

TEST ANALOG OUTPUT

In addition to the simulation modes, the

TEST ANALOG OUTPUT

settings group may be used

during startup or testing to verify that the analog outputs are functioning correctly.

The analog outputs can only be forced if the motor is stopped and there are no trips,
alarms, or start blocks active. When the

FORCE ANALOG OUTPUTS FUNCTION

is “Enabled”,

the output reflects the forced value as a percentage of the 4 to 20 mA or 0 to 1 mA range.
Selecting “Disabled” places all four analog output channels back in service, reflecting the
parameters programmed to each. If the 469 measures phase current or control power is
cycled, the

FORCE ANALOG OUTPUTS FUNCTION

is automatically disabled and all analog

outputs revert back to their normal state.

Any time the analog outputs are forced, the 469 In Service LED will flash, indicating that the
469 is not in protection mode.

TEST

[

FORCE OPERATION

OF

Range: Disabled, 1 Trip, 2 Auxiliary,

3 Auxiliary, 4 Alarm, 5 Block,
6 Service, All Relays, No Relays

TEST

[

FORCE ANALOG OUT-

PUTS

Range: Enabled, Disabled

MESSAGE

ANALOG OUTPUT 1

FORCED VALUE: 0%

Range: 0 to 100%, step 1

MESSAGE

ANALOG OUTPUT 2

FORCED VALUE: 0%

Range: 0 to 100%, step 1

MESSAGE

ANALOG OUTPUT 3

FORCED VALUE: 0%

Range: 0 to 100%, step 1

MESSAGE

ANALOG OUTPUT 4

FORCED VALUE: 0%

Range: 0 to 100%, step 1

«
...
241
242
243
244
245
...
»

Summary of Contents for 469



















































































































































































































































































































































Reviews:

No comments

Related manuals for 469

Masoneilan 469 Series

Brand: GE Pages: 150

Brand: Viega Pages: 3

Brand: Zamel Pages: 3

Brand: ABB Pages: 52

Brand: National Instruments Pages: 65

Brand: JRI Pages: 7

2 Channel USB Relay Module

Brand: Numato Pages: 19

KFD0-RSH-1.4S.PS2

Brand: Pepperl+Fuchs Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands