GE Multilin 469 Instruction Manual Download | Manualshive

Page: 264 / 338

background image

6–14

469 MOTOR MANAGEMENT RELAY – INSTRUCTION MANUAL

CHAPTER 6: ACTUAL VALUES

6.3.5

Power Metering

PATH: ACTUAL VALUES

ZV

A2 METERING DATA

ZV

POWER METERING

The values for power metering and 3-phase total power quantities are displayed here.
Watthours and varhours can also be seen here.

Note

An induction motor by convention consumes Watts and vars (+Watts and +vars). A
synchronous motor can generate vars (–vars) and feed them back to the power system.

If the

S2 SYSTEM SETUP

ZV

VOLTAGE SENSING

ZV

VOLTAGE TRANSFORMER RATIO

settings

is not programmed, the

THIS FEATURE NOT PROGRAMMED

flash message appears

when an attempt is made to enter this group of messages.

Note

Real Power (hp) is converted directly from Real Power (kW). This display-only value is not
used for protection functions. This message will not display more than 65535 hp regardless
of the actual kW that are being metered.

POWER

[

Z

]

METERING

POWER FACTOR:

0.00

Range: 0.01 to 0.99 Lead or Lag, 0.00,

1.00

MESSAGE

REAL POWER:

0 kW

Range: 0 to ±99999 kW

MESSAGE

REAL POWER:

O hp

Range: 0 to 65535 hp

MESSAGE

REACTIVE POWER:

0 kvar

Range: 0 to ±99999 kvar

MESSAGE

APPARENT POWER:

0 kVA

Range: 0 to 65535 kVA

MESSAGE

POSITIVE WAT-

THOURS:

Range: 0.000 to 999999.999 MWh

MESSAGE

POSITIVE VAR-

HOURS:

Range: 0.000 to 999999.999 Mvarh

MESSAGE

NEGATIVE VAR-

HOURS:

Range: 0.000 to 999999.999 Mvarh

MESSAGE

TORQUE:

000.0 Nm

Range: 0.00 to 999999.9 Nm. Seen only

if torque metering is enabled

«
...
262
263
264
265
266
...
»

Summary of Contents for 469



















































































































































































































































































































































Reviews:

No comments

Related manuals for 469

Brand: Omicron Pages: 114

Brand: National Instruments Pages: 16

Brand: Moeller Pages: 2

Brand: Moeller Pages: 2

Brand: Moeller Pages: 2

Brand: Moeller Pages: 2

Brand: BARIX Pages: 20

Brand: IFM Electronic Pages: 49

Brand: LEGRAND Pages: 2

Brand: LEGRAND Pages: 2

Brand: LEGRAND Pages: 4

Brand: LEGRAND Pages: 4

Brand: LEGRAND Pages: 4

Brand: Valcom Pages: 4

Brand: Fujitsu Pages: 6

Brand: Fujitsu Pages: 7

Brand: Fujitsu Pages: 7

Brand: Eaton Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands