GE Multilin 469 Instruction Manual Download | Manualshive

Page: 148 / 338

background image

5–6

469 MOTOR MANAGEMENT RELAY – INSTRUCTION MANUAL

CHAPTER 5: SETTINGS

5.1.2

Trips, Alarms, and Blocks

The 469 has three basic categories of protection elements. They are

trips

,

alarms

, and

blocks

.

•

TRIPS:

A 469 trip feature may be assigned to any combination of the two Auxiliary

relays, 2 AUXILIARY and 3 AUXILIARY, in addition to the 1 TRIP Relay. If a Trip becomes
active, the appropriate LED (indicator) on the 469 faceplate will illuminate to show
which of the output relays has operated. In addition to the Trip relay(s), a trip will
always operate the Block Start relay. Trip features are may be programmed as latched
or unlatched. Once a relay has been operated by a latched trip, a reset must be
performed to clear the trip when the condition is no longer present. If there is a lockout
time, the Block Start relay will not reset until the lockout time has expired. If an
unlatched trip feature becomes active, that trip will reset itself (and associated output
relays) as soon as the condition that caused the trip ceases. Immediately prior to
issuing a trip, the 469 takes a snapshot of motor parameters and stores them as pre-
trip values which will allow for troubleshooting after the trip occurs. The cause of last
trip message is updated with the current trip and the 469 display defaults to that
message. All trip features are automatically logged and date and time stamped as
they occur. In addition, all trips are counted and logged as statistics such that any long
term trends may be identified.

•

ALARMS:

A 469 alarm feature may be assigned to operate any combination of three

output relays, 4 ALARM, 3 AUXILIARY, and 2 AUXILIARY. When an Alarm becomes
active, the appropriate LED (indicator) on the 469 faceplate will illuminate when an
output relay(s) has operated. Each alarm feature may be programmed as latched or
unlatched. Once a latched alarm feature becomes active, the reset key must be
pressed to reset that alarm. If the condition that has caused the alarm is still present
(e.g. hot RTD) the Alarm relay(s) will not reset until the condition is no longer present. If

MESSAGE

TEST

[

See page –101.

MESSAGE

COMMUNICATION

[

See page –102.

MESSAGE

GE

MULTILIN

[

Z

]

See page –102.

MESSAGE

END OF PAGE

SETTINGS

[

SPEED2

[

See page –103.

MESSAGE

SPEED2

[

See page –107.

MESSAGE

SPEED2

[

See page –107.

MESSAGE

END OF PAGE

«
...
146
147
148
149
150
...
»

Summary of Contents for 469



















































































































































































































































































































































Reviews:

No comments

Related manuals for 469

Brand: Keithley Pages: 33

Brand: FANOX Pages: 112

Brand: FANOX Pages: 138

Brand: FANOX Pages: 151

Brand: FANOX Pages: 188

Brand: FANOX Pages: 311

Brand: FANOX Pages: 99

Brand: Anly Pages: 2

Brand: Ampcontrol Pages: 59

Brand: ASO Safety Solutions Pages: 52

Brand: Woodward Pages: 25

Brand: Woodward Pages: 62

Brand: Woodward Pages: 91

DOWNUNDER OUT TCD

Brand: Schrack Technik Pages: 5

Brand: MULTISPAN Pages: 4

Brand: Leuze Pages: 25

Brand: Leuze Pages: 26

Brand: Leuze Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands