Fujitsu F2 MC-8FX Family Hardware Manual Download | Manualshive

Page: 546 / 602

background image

532

CHAPTER 28 256-KBIT FLASH MEMORY

28.5.3

Execution Time-out Flag (DQ5)

The execution time-out flag (DQ5) is a hardware sequence flag indicating that the
automatic algorithm has been executed beyond the specified time (required for
programming/erasing) internal to the flash memory.

■

Execution Time-out Flag (DQ5)

Table 28.5-7 and Table 28.5-8 show the state transition of the execution time-out flag.

●

At programming and chip erasing

When read access is made with the write or chip-erase automatic algorithm invoked, the flag outputs "0"

when the algorithm execution time is within the specified time (required for programming/erasing) or "1"

when it exceeds that time.

The execution time-out flag (DQ5) can be used to check whether programming/erasing has succeeded or

failed regardless of whether the automatic algorithm has been running or terminated. When the execution

time-out flag (DQ5) outputs "1", it indicates that programming has failed if the automatic algorithm is still

running for the data polling or toggle bit function.

If an attempt is made to write "1" to a flash memory address holding "0", for example, the flash memory is

locked, preventing the automatic algorithm from being terminated and valid data from being output from

the data polling flag (DQ7). As the toggle bit flag (DQ6) does not stop toggling, the time limit is exceeded

and the execution time-out flag (DQ5) outputs "1". The state in which the execution time-out flag (DQ5)

outputs "1" means that the flash memory has not been used correctly; it does not mean that the flash

memory is defective. When this state occurs, execute the reset command.

Table 28.5-7 State Transition of Execution Time-out Flag (During Normal Operation)

Operating state

Programming

→

Programming completed

Chip erasing

→

Erasing completed

DQ5

0

→

DATA: 5

0

→

1

Table 28.5-8 State Transition of Execution Time-out Flag (During Abnormal Operation)

Operating state

Programming

Chip erasing

DQ5

1

1

«
...
544
545
546
547
548
...
»

Summary of Contents for F2 MC-8FX Family



























































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for F2 MC-8FX Family

SISPM1040-582-LRT

Brand: Lantronix Pages: 2

Brand: Lantronix Pages: 7

Brand: TC Electronic Pages: 55

Brand: Grundig Pages: 24

Brand: Z3 Technology Pages: 67

JetStor NAS 724UX

Brand: AC&NC Pages: 117

500 - DATASHEET REV 003

Brand: Intel Pages: 67

PXI PXITM -1000

Brand: National Instruments Pages: 55

SFD-2 MkIII Jumper

Brand: Anthem Audio Pages: 2

Tamar FCSAS102800

Brand: Bridgeworks Pages: 56

HFisolator 9730/26-11

Brand: Stahl Pages: 2

Brand: Digital Equipment Pages: 90

Brand: H3C Pages: 34

Brand: Fast Pages: 66

airPoint Nexus sB3210

Brand: SmartBridges Pages: 55

Brand: ZyXEL Communications Pages: 114

9500S-8 - Escalade RAID Controller

Brand: 3Ware Pages: 46

Brand: Vecow Pages: 146

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands