manualshive.com logo in svg

Fujitsu F2 MC-8FX Family, Hardware Manual

The Fujitsu F2 MC-8FX Family Operation Manual is available for free download on our website. This comprehensive manual provides detailed instructions and guidelines for optimizing the performance of your Fujitsu F2 MC-8FX Family device. Visit manualshive.com to access this valuable resource and enhance your user experience.

Share
Download
background image

525

CHAPTER 28  256-KBIT FLASH MEMORY

Table 28.3-1  Functions of Flash Memory Status Register (FSR) 

Bit name

Function

bit7
bit6

-: Undefined bits

The value read is always "0". Writing has no effect on the operation.

bit5

RDYIRQ:
Flash memory 
operation flag bit

This bit shows the operating state of flash memory.
The RDYIRQ bit is set to "1" upon completion of the flash memory automatic algorithm when flash 
memory programming/erasing is completed.
• An interrupt request occurs when the RDYIRQ bit is set to "1" if interrupts triggered by the 

completion of flash memory programming/erasing have been enabled (FSR:IRQEN = 1).

• If the RDYIRQ bit is set to "0" when flash memory programming/erasing is completed, further 

flash memory programming/erasing is disabled.

Setting the bit to "0": Clears the bit.
Setting the bit to "1": Has no effect on the operation.
"1" is read from the bit whenever a read-modify-write (RMW) instruction is used.

bit4

RDY: 
Flash memory 
program/erase status 
bit

This bit shows the programming/erasing status of flash memory.
• Flash memory programming/erasing cannot be performed with the RDY bit set to "0".
• A read/reset command can be accepted even when the RDY bit contains "0". The RDY bit is set to 

"1" upon completion of programming/erasing.

• It takes a delay of two machine clock (MCLK) cycles after the issuance of a program/erase 

command for the RDY bit to be set to "0". Read this bit after, for example, inserting NOP twice 
after issuing the program/erase command.

bit3

Reserved:
Reserved bit

Be sure to set this bit to "0".

bit2

IRQEN: 
Flash memory 
program/erase interrupt 
enable bit

This bit enables or disables the generation of interrupt requests in response to the completion of flash 
memory programming/erasing.
Setting the bit to "1": Causes an interrupt request to occur when the flash memory operation flag 

bit is set to "1" (FSR:RDYIRQ = 1).

Setting the bit to "0": Prevents an interrupt request from occurring even when the flash memory 

operation flag bit is set to "1" (FSR:RDYIRQ = 1).

bit1

WRE: 
Flash memory 
program/erase enable 
bit

This bit enables or disables the programming/erasing of data into/from the flash memory area.
Set the WRE bit before invoking a flash memory program/erase command.
Setting the bit to "0": Prevents a program/erase signal from being generated even when a 

program/erase command is input.

Setting the bit to "1": Allows flash memory programming/erasing to be performed after a 

program/erase command is input.

• When flash memory is not to be programmed or erased, set the WRE bit to "0" to prevent it from 

being accidentally programmed or erased.

• To program data into the flash memory, set FSR:WRE to "1" to write-enable the flash memory and 

set the flash memory sector write control register (SWRE0/SWRE1). When FSR:WRE disables 
programming (contains "0"), write access to flash memory does not take place even though it is 
enabled by the flash memory write control register (SWRE0/SWRE1).

bit0

Reserved:
Reserved bit

Be sure to set this bit to "0".

Summary of Contents for F2 MC-8FX Family



























































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for F2 MC-8FX Family

Barracuda Networks Network Quick Start Manual preview
Network
Brand: Barracuda Networks Pages: 2
D-Link xStack Storage DSN-4000 Series Datasheet preview
xStack Storage DSN-4000 Series
Brand: D-Link Pages: 5
Dahua DHI-NVR2104-P-4KS2 Quick Start Manual preview
DHI-NVR2104-P-4KS2
Brand: Dahua Pages: 23
Juniper NFX250 Quick Start Manual preview
NFX250
Brand: Juniper Pages: 7
Buffalo LinkStation Mini User Manual preview
LinkStation Mini
Brand: Buffalo Pages: 71
AC&NC JetStor NAS 724UX User Manual preview
JetStor NAS 724UX
Brand: AC&NC Pages: 117
Intel IXP45X Developer'S Manual preview
IXP45X
Brand: Intel Pages: 958
Comway 4G DTU Configuration Instructions preview
4G DTU
Brand: Comway Pages: 20
Xtreme SNMP-2PV2 User & Installation Manual preview
SNMP-2PV2
Brand: Xtreme Pages: 83
Radica Games DAVID-II 716 Operating And Maintenance Instruction Manual preview
DAVID-II 716
Brand: Radica Games Pages: 40
Airvana ipBTS C30 Installation And Commissioning Manual preview
ipBTS C30
Brand: Airvana Pages: 90
Renesas HD74HCT1G04 Datasheet preview
HD74HCT1G04
Brand: Renesas Pages: 8
ST X-NUCLEO-EEPRMA1 User Manual preview
X-NUCLEO-EEPRMA1
Brand: ST Pages: 22
Extron electronics VERSATOOLS MTP User Manual preview
VERSATOOLS MTP
Brand: Extron electronics Pages: 19
H3C BT1004E Manual preview
BT1004E
Brand: H3C Pages: 34
Carrier 40VMW005 Installation And Maintenance Instructions Manual preview
40VMW005
Brand: Carrier Pages: 18
Qvis 72-8P Series User Manual preview
72-8P Series
Brand: Qvis Pages: 233
MA Master Fader 1 User Manual preview
Master Fader 1
Brand: MA Pages: 4

Brands by name

Popular brands

Load more brands