Fujitsu F2 MC-8FX Family Hardware Manual Download

Page: 414 / 602

400

CHAPTER 22 I

■

Stop Condition

The master can release the bus and end communications by generating a stop condition. Changing the

SDA0 line from "L" to "H" while SCL0 is "H" generates a stop condition. This signals to the other devices

on the bus that the master has finished communications (referred to below as "bus free"). However, the

master can continue to generate start conditions without generating a stop condition. This is called a

repeated start condition.

Writing "0" to the IBCR10:MSS bit during an interrupt while in bus master mode (IBCR10:MSS = 1,

IBSR0:BB = 1, IBCR10:INT = 1, and IBCR00:ALF = 0) generates a stop condition and changes to slave

mode. In other cases, writing "0" to the IBCR10:MSS bit is ignored.

■

Arbitration

The interface circuit is a true multi-master bus able to connect multiple master devices. Arbitration occurs

when another master within the system simultaneously transfers data during a master transfer.

Arbitration occurs on the SDA0 line while the SCL0 line is at the "H" level. When the send data is "1" and

the data on the SDA0 line is "L" at the master, this is treated as arbitration lost. In this case, data output is

halted and IBCR00:ALF is set to "1". If this occurs, an interrupt is generated if arbitration lost interrupts

have been enabled (IBCR00:ALE = 1). If IBCR00:ALF is set to "1", the module sets IBCR10:MSS = 0 and

IBSR0:TRX = 0, clears TRX, and goes to slave receive mode.

If IBCR00:ALF is set to "1" when IBSR0:BB = 0, IBCR00:ALF is cleared only by writing "0". If

IBCR00:ALF is set to "1" when IBSR0:BB = 1, IBCR00:ALF is cleared only by clearing IBCR10:INT to

"0".

●

Conditions for generating an arbitration lost interrupt when IBSR0:BB = "0"

When a start condition is generated by the program (by setting the IBCR10:MSS bit to "1") at the timing

shown in Figure 22.7-3 or Figure 22.7-4, interrupt generation (IBCR10:INT bit = 1) is prohibited by

arbitration lost detection (IBCR00:ALF = 1).

•

Conditions (1) in which no interrupt is generated due to arbitration lost

If the program triggers a start condition (by setting the IBCR10:MSS bit to "1") when no start condition has

been detected (IBSR0:BB bit = 0) and the SDA0 and SCL0 line pins are at the "

" level.

Figure 22.7-3 Timing Diagram with No Interrupt Generated with IBCR00:ALF = 1

"L"

SCL0 or SDA0 pin at "L" level

SCL0 pin

SDA0 pin

C operation enabled (ICCR0:EN bit = 1)

Master mode set (IBCR10:MSS bit = 1)

Arbitration lost detection bit

(IBCR00:ALF bit = 1)

Bus busy (IBSR0:BB bit)

Interrupt (IBCR10:INT bit)

Summary of Contents for F2 MC-8FX Family



























































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for F2 MC-8FX Family

Reviews:

Related manuals for F2 MC-8FX Family

Brands by name

Popular brands

Fujitsu F2 MC-8FX Family, Hardware Manual

Search results

Summary of Contents for F2 MC-8FX Family

Reviews:

Related manuals for F2 MC-8FX Family

Brands by name

Popular brands