Fujitsu F2 MC-8FX Family Hardware Manual Download | Manualshive

Page: 355 / 602

background image

341

CHAPTER 20 UART/SIO

20.5.5

UART/SIO Serial Output Data Register (TDR0)

The UART/SIO serial output data register (TDR0) is used to output (transmit) serial data.

■

UART/SIO Serial Output Data Register (TDR0)

Figure 20.5-6 shows the bit configuration of the UART/SIO serial output data register.

Figure 20.5-6 UART/SIO Serial Output Data Register (TDR0)

This register holds data to be transmitted. The register accepts a write when the transmission data register

empty (TDRE) bit contains "1". An attempt to write to the bit is ignored when the bit contains "0".

When this register is updated at writting complete the transmission data and TDRE=0 (without depending

on TXE of the UART/SIO serial mode control register is "1" or "0"), the transmission operation is

initialized by writing "0" to TXE, TDRE becomes "1", and the update of this register becomes possible.

Moreover, when "0" is written in TXE without the starting transmission (when the transmission data is

written in TDR, and it has not transmitted TXE to "1" yet), TCPL is not set in "1". The transmission data is

transferred to the shift register for the transmission, it is converted into the serial data, and it is transmitted

from the serial data output terminal.

When transmit data is written to the UART/SIO serial output data register (TDR0), the transmission data

register empty bit (TDRE) is set to "0". Upon completion of transfer of transmit data to the transmission

shift register, the transmission data register empty bit (TDRE) is set to "1", allowing the next piece of

transmit data to be written. At this time, an interrupt occurs if transmission data register empty interrupts

have been enabled. Write the next piece of transmit data when transmit data empty occurs or the transmit

data empty (TDRE) bit is set to "1".

When the character bit length (CBL1, 0) is set to shorter than 8 bits, the excess upper bits (beyond the set

bit length) are ignored.

Note:

The data in this register cannot be updated when TDRE in UART/SIO serial status data register is
"0".
When this register is updated at writting complete the transmission data and TDRE=0 (without
depending on TXE of the UART/SIO serial mode control register 2 is "1" or "0"), the transmission
operation is initialized by writing "0" to TXE, TDRE becomes "1", and the update of this register
becomes possible.
Moreover, when "0" is written in TXE without the starting transmission (when the transmission data is
written in TDR, and it has not transmitted TXE to "1" yet), TCPL is not set in "1". And, to change
data, please write it after making TDRE "1" once by writing TXE =0.

Address

bit7

bit6

bit5

bit4

bit3

bit2

bit1

bit0

Initial value

0059

H

TDR0

TD7

TD6

TD5

TD4

TD3

TD2

TD1

TD0

00000000

B

R/W

R/W

R/W

R/W

R/W

R/W

R/W

R/W

R/W : Readable/writable (Read value is the same as write value)

«
...
353
354
355
356
357
...
»

Summary of Contents for F2 MC-8FX Family



























































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for F2 MC-8FX Family

Brand: M-Audio Pages: 10

Brand: Xinje Pages: 57

Brand: Blackrock Microsystems Pages: 27

Brand: Commell Pages: 9

Hollywood DV-Bridge

Brand: Dazzle Pages: 63

Brand: Buffalo Pages: 2

OMB-DAQBOARD-500 Series

Brand: Omega Pages: 48

Brand: Rainbow Pages: 2

Brand: Intercoax Pages: 2

Brand: Softing Pages: 16

Brand: Datum Pages: 49

Brand: Freescale Semiconductor Pages: 124

Brand: IEI Technology Pages: 146

Brand: Brickcom Pages: 184

Brand: Proxim Pages: 65

Brand: NEC Pages: 170

StudioStation 100

Brand: Extron electronics Pages: 131

CloudVision DCA-100-CV

Brand: Arista Pages: 46

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands