Foundry Switch and Router Installation and Configuration Guide
20 - 6
December 2000
These commands configure a standard ACL for the private sub-net 10.10.10.x/24, then enable inside NAT for the
sub-net. Make sure you specify
permit
in the ACL, rather than
deny
. If you specify
deny
, the Foundry device will
not provide NAT for the addresses.
Example with Port Address Translation Enabled
To configure dynamic NAT with the Port Address Translation feature enabled, enter commands such as the
following at the global CONFIG level of the CLI:
BigIron(config)# access-list 1 permit 10.10.10.0/24
BigIron(config)# ip nat pool OutAdds 209.157.1.2 209.157.1.254 prefix-length 24
BigIron(config)# ip nat inside source list 1 pool OutAdds overload
These commands are the same as the ones in “Example with Port Address Translation Disabled”, except the
ip
nat inside source
command uses the
overload
parameter. This parameter enables the Port Address Translation
feature.
Command Syntax
Syntax:
[no] ip nat pool <pool-name> <start-ip> <end-ip> netmask <ip-mask> | prefix-length <length>
This command configures the address pool.
The <pool-name> parameter specifies the pool name. The name can be up to 255 characters long and can
contain special characters and internal blanks. If you use internal blanks, you must use quotation marks around
the entire name.
The <start-ip> parameter specifies the IP address at the beginning of the pool range. Specify the lowest-
numbered IP address in the range.
The <end-ip> parameter specifies the IP address at the end of the pool range. Specify the highest-numbered IP
address in the range.
NOTE:
The address range cannot contain any gaps. Make sure you own all the IP addresses in the range. If
the range contains gaps, you must create separate pools containing only the addresses you own.
The
netmask
<ip-mask> |
prefix-length
<length> parameter specifies a classical sub-net mask (example:
netmask
255.255.255.0) or the length of a Classless Interdomain Routing prefix (example:
prefix-length
24
).
NOTE:
The maximum number of global IP addresses you can configure depends on how much memory the
Layer 3 Switch has and whether you enable the Port Address Translation feature. Regardless of the amount of
memory, you cannot configure more than 256 global IP addresses.
Syntax:
[no] ip nat inside source list <acl-name-or-num> pool <pool-name> [overload]
This command associates a private address range with a pool of Internet addresses and optionally enables the
Port Address Translation feature.
The
inside source
parameter specifies that the translation applies to private addresses sending traffic to global
addresses (Internet addresses).
The
list
<acl-name-or-num> parameter specifies a standard or extended ACL. You can specify a numbered or
named ACL.
NOTE:
For complete standard and extended ACL syntax, see “Using Access Control Lists (ACLs)” on page 13-
1.
The
pool
<pool-name> parameter specifies the pool. You must create the pool before you can use it with this
command.
The
overload
parameter enables the Port Address Translation feature. Use this parameter if the IP address pool
does not contain enough addresses to ensure NAT for each private address. The Port Address Translation
feature conserves Internet addresses by mapping the same Internet address to more than one private address
Summary of Contents for Switch and Router
