![background image](http://html.mh-extra.com/html/foundry-networks/switch-and-router/switch-and-router_installation-and-configuration-manual_2324275802.webp)
Foundry Switch and Router Installation and Configuration Guide
19 - 120
December 2000
•
RFC 2842. This RFC specifies the Capability Advertisement, which a BGP4 router uses to dynamically
negotiate a capability with a neighbor.
•
RFC 2858 for Multi-protocol Extension.
NOTE:
The Foundry implementation of dynamic route refresh supports negotiation of IP version 4 unicasts
only.
•
bgp-draft-route-refresh-1.txt, which describes the dynamic route refresh capability
The dynamic route refresh capability is enabled by default when you upgrade to software release 07.1.00 and
cannot be disabled. When the Layer 3 Switch sends a BGP4 OPEN message to a neighbor, the Layer 3 Switch
includes a Capability Advertisement to inform the neighbor that the Layer 3 Switch supports dynamic route
refresh.
NOTE:
The option for dynamically refreshing routes received from a neighbor requires the neighbor to support
dynamic route refresh. If the neighbor does not support this feature, the option does not take effect and the
software displays an error message. The option for dynamically re-advertising routes to a neighbor does not
require the neighbor to support dynamic route refresh.
To use the dynamic refresh feature, use either of the following methods.
Dynamically Refreshing Routes
The following sections describe how to dynamically refresh BGP4 routes to place new or changed filters into
effect.
USING THE CLI
To request a dynamic refresh of all routes from a neighbor, enter a command such as the following:
BigIron(config-bgp-router)# clear ip bgp neighbor 192.168.1.170 soft in
This command asks the neighbor to send its BGP4 table (Adj-RIB-Out) again. The Layer 3 Switch applies its
filters to the incoming routes and adds, modifies, or removes BGP4 routes as necessary.
Syntax:
clear ip bgp neighbor all | <ip-addr> | <peer-group-name> | <as-num> [soft-outbound | soft [in | out]]
The
all
| <ip-addr> | <peer-group-name> | <as-num> specifies the neighbor. The <ip-addr> parameter specifies a
neighbor by its IP interface with the Layer 3 Switch. The <peer-group-name> specifies all neighbors in a specific
peer group. The <as-num> parameter specifies all neighbors within the specified AS. The
all
parameter specifies
all neighbors.
The
soft-outbound
parameter updates all outbound routes by applying the new or changed filters, but sends only
the existing routes affected by the new or changed filters to the neighbor.
The
soft [in | out]
parameter specifies whether you want to refresh the routes received from the neighbor or sent
to the neighbor:
•
soft in
requests the neighbor’s entire BGP4 route table (Adj-RIB-Out), then applies the filters to add, change,
or exclude routes.
•
soft out
updates all outbound routes, then sends the Layer 3 Switch’s entire BGP4 route table (Adj-RIB-Out)
to the neighbor, after changing or excluding the routes affected by the filters.
If you do not specify
in
or
out
, the Layer 3 Switch performs both options.
NOTE:
The
soft-outbound
parameter updates all outbound routes by applying the new or changed filters, but
sends only the existing routes affected by the new or changed filters to the neighbor. The
soft out
parameter
updates all outbound routes, then sends the Layer 3 Switch’s entire BGP4 route table (Adj-RIB-Out) to the
neighbor, after changing or excluding the routes affected by the filters. Use
soft-outbound
if only the outbound
policy is changed.
To dynamically resend all the Layer 3 Switch’s BGP4 routes to a neighbor, enter a command such as the
following:
Summary of Contents for Switch and Router
