Foundry Switch and Router Installation and Configuration Guide
21 - 16
December 2000
NOTE:
You cannot set the priority of a VRRP Owner. The Owner’s priority is always 255.
VRRPE Syntax
Syntax:
backup [priority <value>] [track-priority <value>]
The software requires you to identify a VRRPE interface as a Backup for its VRID before you can activate the
interface for the VRID. However, after you configure the VRID, you can use this command to change its priority or
track priority. The parameter values are the same as for VRRP.
Suppression of RIP Advertisements on Backup Routers for the Backup Up Interface
Normally, a VRRP or VRRPE Backup includes route information for the virtual IP address (the backed up
interface) in RIP advertisements. As a result, other routers receive multiple paths for the backed up interface and
might sometimes unsuccessfully use the path to the Backup rather than the path to the Master.
You can prevent the Backups from advertising route information for the backed up interface by enabling
suppression of the advertisements.
USING THE CLI
To suppress RIP advertisements for the backed up interface in Router2, enter the following commands:
Router2(config)# router rip
Router2(config-rip-router)# use-vrrp-path
Syntax:
use-vrrp-path
The syntax is the same for VRRP and VRRPE.
Hello Interval
The Master periodically sends Hello messages to the Backups. The Backups use the Hello messages as
verification that the Master is still on-line. If the Backup routers stop receiving the Hello messages for the period of
time specified by the Dead interval, the Backup routers determine that the Master router is dead. At this point, the
Backup router with the highest priority becomes the new Master router. The Hello interval can be from 1 – 84
seconds. The default is 1 second.
NOTE:
The default Dead interval is three times the Hello Interval plus one-half second. Generally, if you change
the Hello interval, you also should change the Dead interval on the Backup routers.
USING THE CLI
To change the Hello interval on the Master to 10 seconds, enter the following commands:
Router1(config)# inter e 1/6
Router1(config-if-1/6)# ip vrrp vrid 1
Router1(config-if-1/6-vrid-1)# hello-interval 10
Syntax:
hello-interval <value>
The syntax is the same for VRRP and VRRPE.
Dead Interval
The Dead interval is the number of seconds a Backup waits for a Hello message from the Master before
determining that the Master is dead. When Backups determine that the Master is dead, the Backup with the
highest priority becomes the new Master. The Dead interval can be from 1 – 84 seconds. The default is 3.5
seconds. This is three times the default Hello interval (1 second) plus one-half second added by the router
software. The software automatically adds one-half second to the Dead interval value you enter.
USING THE CLI
To change the Dead interval on a Backup to 30 seconds, enter the following commands:
Router2(config)# inter e 1/5
Summary of Contents for Switch and Router
