482
* The miniSD memory card is optional for use in this terminal.
→
p.353
If
A
n
y
E
rror
M
e
ss
ag
e A
p
p
ear
s
Appendix/External Devices/Troubleshootin
g
“No requested software”
d
This message appears when you select a desktop icon for already
deleted i-
α
ppli.
d
This message appears if there is no corresponding software when
the i-
α
ppli is launched from a mail message, the infrared data
exchange function, the bar code reader or the IC card.
−
“Unable to retrieve the requested
URL (504)”
d
The attempt to access a site has failed for some reason. Retry
connection.
−
“Invalid address”
d
The address contains a “,” and is invalid. Delete any “,”.
d
The address of the received message contains more than 50 single-
byte characters, and you cannot reply to it.
d
SMS cannot be sent because the address contains a space or
character other than numbers, “#” and “
*
”. Delete any spaces or
characters other than numbers, “#” and “
*
”.
−
“Activating restrict dialing”
d
This message appears when you attempt to perform a prohibited
operation when the restrict dialing is set.
p.171
“Please wait”
d
The voice line or packet communication device may be
malfunctioning. Otherwise, the voice line/packet communication
network may be congested. Attempt to use a voice call, videophone
call or i-mode later.
You can still make an emergency call (110, 119 and 118). However,
you may not be connected depending on the condition.
−
“Please wait for a while (packet)”
d
The packet communication device may be malfunctioning. Otherwise,
the packet communication network may be congested. Retry later.
−
“Other function active Cannot
start”
“Other function active Cannot
operate”
d
This message appears when you attempt to perform an unavailable
operation but another function is running.
−
“i-
α
ppli stand-by display
terminated due to security error”
“Software terminated due to
security error”
d
This message appears when the i-
α
ppli or the i-
α
ppli standby screen
(including the i-
α
ppli DX) terminated because you attempted to
perform an unauthorized operation.
p.294
p.301
(During infrared data exchange)
“No response Retry?”
d
The receiving terminal cannot be found/detected. Place the
terminals so that their infrared data ports face each other. Select
“YES” and press
d
to try again.
p.365
“Connection interrupted”
d
i-mode connection was interrupted due to poor reception. Move to a
location where the reception is good before using the i-mode service.
d
If this message appears even when the reception is good and “
”
appears, the site you are accessing is busy. Retry later.
p.213
−
“Connection failed”
d
This message appears when the host setting is not correct. Set the
host correctly in “Host selection” under Connection setting.
d
The attempt to connect to i-mode has failed for some reason. Retry
connection.
p.228
−
“Connection failed”
d
Set “Caller ID Notification” to “ON” and retry.
p.47
“Time out”
d
Accessing a site or sending a message was interrupted because the
time, which is set in “Set connection timeout”, has elapsed. Retry
later.
p.228
“Failed to Copy all”
d
The data cannot be copied due to some error. Exchange with a new
miniSD memory card then retry to copy.
−
“Some addresses is invalid”
d
This message appears when you attempt to reply to two or more
addresses but not all addresses are valid.
−
“This software contains an error”
“This software contains an error
Unable to download”
d
This message appears when the software data contains an error and
you cannot download or upgrade the software.
−
“Software is stopped because of
error”
d
This message appears when you are running a program and an
error occurs preventing further operation.
−
“This software is not supported by
this phone”
d
This message appears when the software you attempt to download
is incompatible with the FOMA terminal and cannot be downloaded.
−
“Not correspond contents”
d
Information read by the Bar code reader cannot be recognized
because there are some contents unsupported by the FOMA terminal.
−
Error Message
Explanation and Solution
Refer to