Flintec FT-111 AN Technical Manual Download Page 144

Page: 144 / 146

FT-111(D) Panel Weighing Indicator, Technical Manual, Rev.1.0.0, May 2019

Page

143

146

- Change E

ROM ( U13 ).

E28 CLOCK ERROR

Clock error.

- Change CR2032 battery.
- Change the main board.

E32 LABEL ERROR

Checksum error of EPL printout
format.

- Press enter key and re-load the EPL
code.
- Change E

ROM ( U13 ).

E34 NOT LOADED

ADC output is not changed for the
span calibration.

- Recalibrate the scale.
- Change mainboard.

E35 LC CONNECTIO

The load cell output is decreased
after loading.

- Check load cell connections.
- Check test weight loading.
- Recalibrate the scale.
- Change mainboard.

E36 ADD LOAD

The load is not enough for span
calibration.

E37 UNSTABLE

The load is not stable at
calibration.

- Wait until scale become stable.
- Check grounding wiring.
- Recalibrate the scale.
- Change mainboard.

E40 NO ALIBI SD

Alibi memory SD card is not
installed.

- Disable Alibi memory if not required.
- Check Alibi SD card.
- Change mainboard.

E41 ALIBI FAULT

Alibi SD card is not supplied from
FLINTEC.

- Install Flintec Alibi SD card.

E42 NEW ALIBI

Alibi memory serial number error.
The new alibi SD card is installed.

- Format the alibi memory SD
card. Refer to parameter 816.

E43 ALIBI ERROR

Alibi memory could not be
initialized.

- Check alibi memory SD card
- Change main board.

E44 ALIBI CSUM E

Alibi CSUM error.

- Check alibi memory records.
- Change Alibi memory SD card.
- Change main board.

E47 ALIBI CSUM E

Alibi information CSUM error.

E48 ALIBI SD ERR

Wrong SD card at alibi memory.

- Order Alibi SD card.

E50 DLC CARD FAI

The DLC Board is broken or not
installed.

- Re-energize indicator.
- Change the DLC Board.

E61 FLASH ERROR

E2PROM Error.

- Change main board.

E70 MB SELECT ER

Modbus selection error

- Check data format of other interfaces.
- Other interfaces should not be
Modbus.

E75 MODBUS FAULT

The Modbus SD card is not
installed in SD2 card slot.

- Order Modbus SD card.
- Install Flintec Modbus SD card.

E80 VERIFY SCALE

Reverification the scale.

- Reverify the scale after checking the
scale hardware, load cells,
performance etc.

E81 CANNOT ADDR

DLC could not addressed.

- Check the DLC connection (RS-485 &
Power supply) hardware.
- Check the DLC and S/N.

E82 SHIFT ADJUST

Shift adjustment is not available
due to load cell coefficients are out
of limits.

- Check addressing is done correctly.
- Check test weight loading on
the correct DLC.
- Check the load cell installation and
scale installation.

E83 DLC COUNT ER

No regular response from load cell

- Reenergize the indicator.
- Check the DLC connection (RS-485 &
Power supply).
- Change load cell.

Summary of Contents for FT-111 AN



















































































































































Search results

Summary of Contents for FT-111 AN

Reviews:

Related manuals for FT-111 AN

Brands by name

Popular brands

Flintec FT-111 AN, Technical Manual

Search results

Summary of Contents for FT-111 AN

Reviews:

Related manuals for FT-111 AN

Brands by name

Popular brands