Ezgo 611103 Service & Repair Manual Download | Manualshive

Page: 60 / 186

background image

Page E-6

ELECTRONIC SPEED CONTROL (AC MOTOR)

Repair and Service Manual

Read all of Section B and this section before attempting any procedure. Pay particular attention to all Notes, Cautions and Warnings.

B

5. Disconnect the Red wire from the controller B+ termi-

nal to the back terminal of the solenoid.

6. Remove two hex head nuts (7) securing the solenoid

to the controller heat sink, place the solenoid off to
one side out of the way.

The original solenoid is

hard wired into the electrical harness.

7. Disconnect the 2 pin connector (14) from the wire har-

ness.

8. Disconnect the 3 pin connector (12) from the resistor

control (13) connector.

9. Disconnect the 23 pin connector (9) from controller by

lifting up on the locking tab and pulling the connector
housing away from the controller.

10. Disconnect the three wires (8) from the electric motor

to terminals U, V and W by removing the three control-
ler terminal screws (11).

11. Disconnect the negative (-) battery wire (3) from the B-

terminal by removing the terminal screw (11).

12. Remove the front two hex head bolts (10) securing the

controller assembly to the floorboard and loosen the
rear hex head bolt (10). Slide the controller towards
the front of the car and lift it out.

Fig. 8 Solenoid Connections

Installation

13. To install the controller, position it on the floorboard;

making sure that all wires are not pinched or under the
controller feet; and slide it to the back aligning the slot
under the head of the hex head bolt (10). Install the
two hex head bolts (10) in the holes at the front of the
controller base. Torque all three hex head bolts as
specified in the torque table.

14. Connect the three wires from the electric motor. Blue

to the W terminal, Yellow to the V terminal and Green
to the U terminal. Install the terminal screws finger
tight, then torque as specified.

Do not over tighten

the terminal screws (11).

15. Connect the black wire (3) from the B- terminal to the

negative (-), BL-, battery terminal.

Do not over

tighten the terminal screw (11).

16. Install the solenoid on the controller heat sink using

two hex head nuts (7). Reconnect the Red positive (+)
battery cable to the front terminal of the solenoid.

Heatsink

Solenoid

Resistor

Wire to
Resistor

Red Wire from
Solenoid to
Controller B+

Controller

Red Wire to
Battery BL+

«
...
58
59
60
61
62
...
»

Summary of Contents for 611103



























































































































































































Reviews:

No comments

Related manuals for 611103

700 Diesel ATV 2007

Brand: Arctic Cat Pages: 184

TOURINO PICK-UP

Brand: Cramer Pages: 16

Brand: Etnyre Pages: 42

Brand: Sakai Pages: 77

GP800Y WaveRunner GP

Brand: Yamaha Pages: 119

FxNytro FX10M53SZ

Brand: Yamaha Pages: 92

FX Nytro FX10MTRY

Brand: Yamaha Pages: 92

Brand: Yamaha Pages: 146

Brand: Yamaha Pages: 182

Brand: Yamaha Pages: 140

Brand: Yamaha Pages: 84

Brand: Yamaha Pages: 76

Brand: Yamaha Pages: 76

Brand: Yamaha Pages: 88

Brand: Yamaha Pages: 92

WARRIOR YFM350XN

Brand: Yamaha Pages: 167

Brand: Yamaha Pages: 227

Brand: Yamaha Pages: 288

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands