Ezgo 611103 Service & Repair Manual Download | Manualshive

Page: 34 / 186

background image

Page C-2

BODY

Repair and Service Manual

Read all of Section B and this section before attempting any procedure. Pay particular attention to all Notices, Cautions and Warnings.

B

BODY COMPONENT REPLACE-
MENT

The body components can be replaced by removing the
securing hardware, replacing the component and install-
ing hardware in the same orientation as it was removed.

Front Bumper and Cowl Support

(Ref. Fig. 3)

Tool List

Qty.

Socket, 15mm.............................................................. 1
Ratchet ........................................................................ 1

1. Remove two hex nuts (11) securing the top of the

bumper to the front strut mounting bolts.

2. Pull top of bumper (12) forward and off of the bolts

then lift upward to clear the frame channel between
the front struts and pull the lower edge of the bumper
down and away from the vehicle.

3. Remove the washers (13).

Reassemble in reverse order. Replace any worn or
damaged hardware as required. It is recommended
that all locking nuts be replaced after 5 removals.

Fig. 3 Front Bumper and Cowl Support

Rocker Panels

(Ref. Fig. 4)

Tool List

Qty.

Torx bit, T-45IP.............................................................1
Ratchet ........................................................................1
Torque Wrench, in. lbs. ................................................1

1. Remove the lower rocker panel (1) by removing three

torx screws (3).

2. Remove the upper rocker panel (2) by removing the

two remaining torx screw (3).

Removal is the same for both sides of the vehicle.

Reassemble in reverse order. Replace any worn or
damaged hardware as required. It is recommended
that all locking nuts be replaced after 5 removals.

Fig. 4 Rocker Panel Removal

Floor Mat

(Ref. Fig. 5) (Ref. Fig. 6)

Tool List

Qty.

Notched Pry Bar ..........................................................1

The upper and lower rocker panels must be removed
before removing the floor mat.

1. Remove six christmas tree rivets (5) securing the floor

mat to the floorboard (4). (Ref. Fig. 5).

2. Pull edge of floor mat from under edge of instrument

panel and lift over accelerator and brake pedals.

ITEM

TORQUE SPECIFICATION

11

27 - 44 in. lbs (3 - 5 Nm)

ITEM

TORQUE SPECIFICATION

3

27 - 44 in. lbs (3 - 5 Nm)

«
...
32
33
34
35
36
...
»

Summary of Contents for 611103



























































































































































































Reviews:

No comments

Related manuals for 611103

Brand: Linhai Pages: 208

Brand: CadKat Pages: 11

Brand: Taylor-Dunn Pages: 244

Brand: Makita Pages: 128

YUM1A UMAX RALLY 2021

Brand: Yamaha Pages: 76

Brand: Yamaha Pages: 158

GRIZZLY YFM70GPAP 2023

Brand: Yamaha Pages: 180

KODIAK ULTRAMATIC YFM400FWAN 2000

Brand: Yamaha Pages: 184

Raider-Classic 150

Brand: Dazon Pages: 79

Brand: Blata Pages: 24

Brand: Kinroad Pages: 38

Brand: LJ'S TOPS & BOTTOMS Pages: 14

eXtreme Sport ES150IIR

Brand: Hammerhead Pages: 67

Brand: Jayco Pages: 100

Brand: Hammerhead Pages: 67

Brand: GARIA Pages: 118

Workman HD Series

Brand: Toro Pages: 318

Brand: Suzuki Pages: 47

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands