ELECTRICAL COMPONENTS & WIRING
Page K-7
Repair and Service Manual
Read all of Section B and this section before attempting any procedure. Pay particular attention to all Notices, Cautions and Warnings.
B
B
.
Fig. 17 Motor Connections (Early Vehicles)
t) NEW STYLE WIRE HARNESS: Plug male con-
nector end of the adaptor harness into the female
connector on the motor sensor harness. Plug the
other end of the adaptor harness connector into
the connector of main harness, push in firmly and
make sure that the locking tab is latched.
Fig. 18 Old Style Motor Connections (Later Vehicles)
u) Connect one end of the adaptor harness to the
motor sensor harness, connect the other end of
the adaptor harness to the main wire harness con-
nector as shown in detail below.
Fig. 19 New Style Motor Connections (later Vehicles)
31. Install the reverse warning indicator (11) onto the con-
troller splash shield using two Torx head screws (10).
32. Press the fuse holder (12) into the hole on the control-
ler splash shield.
Fig. 20 Reverse Warning Indicator & Fuse
33. Install the Run/Tow switch (7)
by removing the upper nut (5)
and seal (4) from the switch.
Position the switch with the
notch towards the RUN direc-
tion. Install the upper nut (5)
finger tight and torque as
specified in the torque table, install the seal (4).
MOTOR
MOTOR
32
31
Motor Sensor
Connector
Adaptor Harness
Main Harness
Connector
Motor Sensor
Connector
Main Wire Harness
Connector
Adaptor
Harness
Motor
31
32
Splash Shield
Failur
e t
o fo
llo
w these instruc
tions can r
esult in SERIOUS INJUR
Y or DEA
TH
Turn the ignition key to the ‘N’
position and ‘chock’
tires to prevent inadvertent movement.
Turn
the
ign
ition
key
to th
e ‘N
’ po
sitio
n an
d ‘c
hoc
k’ tir
es to
pre
ven
t ina
dve
rten
t m
ove
men
t.
Remove this plastic cover by removing 3 plastic fasteners. See illustrations below
.
Rem
ove
this
pla
stic
cov
er b
y re
mov
ing 3
pla
stic
faste
ners
. Se
e illu
stra
tion
s be
low
.
See emergency brake release instruction under this panel.
See
em
erge
ncy
bra
ke re
leas
e in
stru
ctio
n un
der t
his p
ane
l.
609987
609
987
Flip the RUN-T
OW switch to the ‘T
OW’
position and move vehicle to the desired location and
Flip
the
RU
N-T
OW
sw
itch
to th
e ‘T
OW
’ po
sitio
n an
d m
ove
veh
icle
to th
e de
sire
d lo
catio
n an
d
park it properly on level ground and chock tires immediately
.
park
it p
rope
rly o
n le
vel g
roun
d an
d ch
ock
tire
s im
med
iate
ly.
Turn the ignition key to the ‘OFF’
position, remove key and perform required service
Turn
the
ign
ition
key
to th
e ‘O
FF’ p
ositi
on, r
em
ove
key
and
per
form
req
uire
d se
rvic
e
procedures following all Safety Guidelines as outlined in your repair manual.
proc
edu
res f
ollo
win
g all
Sa
fety
Gu
ideli
nes
as o
utlin
ed in
you
r re
pair
man
ual.
IF VEHICLE IS INOPERABLE
AND NEEDS T
O BE MOVED:
IF VE
HICL
E IS IN
OPER
ABLE
AND
NEE
DS TO
BE M
OVED
:
In Case of T
otal Power Loss and the ‘Run-tow’
Switch DOES NOT Release
In Ca
se of
Total
Powe
r Los
s and
the ‘R
un-to
w’ Sw
itch D
OES N
OT R
eleas
e
the Brake to Move the V
ehicle :
the B
rake t
o Mo
ve th
e Veh
icle :
Push center
of fastener
with vehicle
key
,
depressed
remove.
lift fastener to
When center is
To reuse fastener
push center stem
up then install
fastener
shield into
hole.through
To secure fastener
in place press
down on
center stem
with head of
fastener
.
until flush
