Ezgo 611103 Service & Repair Manual Download | Manualshive

Page: 155 / 186

background image

TROUBLESHOOTING AND DIAGNOSTICS

Page O-1

Repair and Service Manual

Read all of Section B and this section before attempting any procedure. Pay particular attention to all Notices, Cautions and Warnings.

B

B

HOW TO USE THE HAND HELD DIAG-
NOSTIC UNIT

The E-Z-GO Hand Held Diagnostic Unit, P/N 606215 is
used for troubleshooting, tuning, programming and the
retrieval of warranty information on the 48V AC golf car.

Fig. 1 Hand Held Diagnostic Unit

The hand held diagnostic unit is connected to the vehi-
cle by plugging the power cord connector into the recep-
tacle located under the vehicle cup holder.

The E-Z-GO logo will display when the unit is first pow-
ered up, then the menu title is displayed on the first line
of the display screen with the menu selections indented
under it.

The vertical bar along the left side of the display screen
moves up and down when buttons 1 or 5 are pressed.
The length of the bar also changes depending on how
many items are in a menu. When the bar is positioned at
the top arrow the beginning of the menu has been
reached; if the bar has reached the arrow at the bottom
of the screen there are no more menu choices available.

To access the different diagnostic functions, use the five
control buttons to scroll through the menus.

Buttons 1 and 5 will move the cursor up and down
through the menu, button 4 will show the sub menu for
the highlighted item. Button 2 will return to the top level
menu. Button 3 is used as ’enter’ or ’return’; hold the
button for 3 seconds.

MENUS

The Hand Held Diagnostic Unit, when connected to the
vehicle, will provide access to information on the follow-
ing:

DIAGNOSTICS REPORT (real time read only)

1. BATTERY VOLTAGE: displayed as ’VOLTAGE’, the

next line displays ’HIGH’, the actual voltage or ’LOW’.
in tenths of a volt

DISPLAY SCREEN

CONTROL BUTTONS

POWER CORD

SERVICE MENU

DIAG REPORT

BATTERY/WARRANTY

ERRORS

WARNINGS

SETUP PERFORMANCE

COURSE ENERGY

BAR

MENU TITLE

HIGHLIGHTED MENU ITEM

ARROW

«
...
153
154
155
156
157
...
»

Summary of Contents for 611103



























































































































































































Reviews:

No comments

Related manuals for 611103

Raider Classic 150

Brand: Dazon Pages: 45

Brand: Baltmotors Pages: 58

500 MXU IRS 4X4

Brand: KYMCO Pages: 1

SPARTAN 600 EFI

Brand: Chironex Pages: 56

Brand: Flagro Pages: 29

Brand: Hisun Pages: 116

2012 Prowler XT

Brand: Arctic Cat Pages: 64

1000 TRV LIMITED

Brand: Arctic Cat Pages: 84

Brand: Dynacraft Pages: 31

Brand: Mi-T-M Pages: 12

Sportsman 800 Big Boss

Brand: Polaris Pages: 143

Brand: Jacobsen Pages: 60

RECOIL iS CREW 2015

Brand: Bad Boy Pages: 60

Brand: Bad Boy Pages: 152

Brand: Taylor-Dunn Pages: 232

E-Z-GO Cushman TITAN 36V HD

Brand: Textron Pages: 60

Brand: Textron Pages: 128

Brand: Toro Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands