Ezgo 611103 Service & Repair Manual Download | Manualshive

Page: 35 / 186

background image

BODY

Page C-3

Repair and Service Manual

Read all of Section B and this section before attempting any procedure. Pay particular attention to all Notices, Cautions and Warnings.

B

B

I

Fig. 5 Floor Mat Fastener Removal

Installation of the floor mat will require new christmas tree
rivets

— install the shorter christmas tree rivets in the

upper corners of floor mat

(Ref. Fig. 6).

Reassemble in reverse order. Replace any worn or
damaged hardware as required.

Fig. 6 Floor Mat

Cowl and Instrument Panel

(Ref. Fig. 7) (Ref. Fig. 8)

Tool LIst

Qty.

Torx bit, T-45IP ............................................................ 1
Torx bit, T-30 ............................................................... 1
Torx bit, T-27IP ............................................................ 1
Insulated Wrench, 9/16" .............................................. 1
Ratchet........................................................................ 1
Torque Wrench, in. lbs................................................. 1
Torque Wrench, ft. lbs ................................................. 1
Long Needle Nose Pliers ............................................ 1

Using an insulated wrench, disconnect the bat-

tery cable at the negative (-), BL-, battery ter-

minal.

If the vehicle is equipped with a sun top and windshield;
remove these items before proceeding. Instructions for
removal of the sun top and windshield are located in the
Weather Protection section of this manual. Remove the
upper and lower rocker panels and the floor mat as
described in the previous sections.

1. Remove four torx screws (11) securing the trim panel

(12) to the instrument panel (13) and cowl (14).

2. Locate the tab in the fender well area, under the cowl.

The tab extends from the instrument panel through a
slot in the cowl, squeeze the legs of the tab together
and push to the back of the vehicle while pulling for-
ward on the cowl. Repeat for the other side —

at this

point the cowl is completely loose

— remove the

cowl.

3. Loosen the trim panel (12) by pulling it away from the

instrument panel along the upper edge then grip the
ball holder with both hands and pull away from the
instrument panel (13); move to the other side of the
vehicle and grip the ball holder on that side with both
hands and pull it away from the instrument panel (13).

4. Disconnect wires to the instruments located in the trim

panel then remove the trim panel.

Fig. 7 Cowl and Instrument Panel Trim

Location of Short
Christmas Tree
Rivets

«
...
33
34
35
36
37
...
»

Summary of Contents for 611103



























































































































































































Reviews:

No comments

Related manuals for 611103

Brand: LaTrax Pages: 36

Brand: Coleman Pages: 12

Brand: Flagro Pages: 28

Brand: Suzuki Pages: 28

Sportsman 800 EFI

Brand: Polaris Pages: 388

Sportsman 850 2021

Brand: Polaris Pages: 180

Brand: JI-EE Pages: 61

MKII 600 Series

Brand: NC ENGINEERING Pages: 80

MARGAY racing K3

Brand: Ignite Pages: 30

Brand: Coleman Powersports Pages: 85

Grizzly YFM600FWAM

Brand: Yamaha Pages: 164

Brand: Yamaha Pages: 182

Brand: Polaris Pages: 4

Cushman Shuttle 4 ELiTE 2020

Brand: Textron Specialized Vehicles Pages: 64

Brand: SMC Networks Pages: 93

Brand: Stinger Pages: 12

Brand: Storti Pages: 109

Brand: Swisher Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands