Ezgo 611103 Service & Repair Manual Download

Page: 107 / 186

BRAKES

Page J-3

Repair and Service Manual

Read all of Section B and this section before attempting any procedure. Pay particular attention to all Notices, Cautions and Warnings.

12. Reconnect electrical harness to rotary position sensor

(8) and to the brake switch (10).

13. Place pedal assembly (5) in position on the floorboard

and secure with four socket head hex screws (6).

14. Install the clevis pin (1) through the brake pedal return

spring arm (2) and secure with the E-clip (3).

15. Tighten the return spring retaining nut (12) to the posi-

tion marked.

16. Install the pedal cover (21), using new christmas tree

rivets (20), replace the floormat and rocker panels.‘

Replace any worn or damaged hardware with new as
required.

‘

ITEM

TORQUE SPECIFICATION

9, 11

12 - 15 in. lbs (1.3 - 1.7 Nm)

354 - 425 in. lbs (40 - 48 Nm)

Summary of Contents for 611103



























































































































































































Search results

Summary of Contents for 611103

Reviews:

Related manuals for 611103

Brands by name

Popular brands

Ezgo 611103, Service & Repair Manual

Search results

Summary of Contents for 611103

Reviews:

Related manuals for 611103

Brands by name

Popular brands