Ezgo 611103 Service & Repair Manual Download Page 61

Page: 61 / 186

ELECTRONIC SPEED CONTROL (AC MOTOR)

Page E-7

Repair and Service Manual

Read all of Section B and this section before attempting any procedure. Pay particular attention to all Notes, Cautions and Warnings.

Make sure that the red wire (17) and black wire (18)
from the wire harness to the solenoid are located as
shown.

17. Install the Red wire to the B+ terminal of the controller.

(Do not over tighten the terminal screw (11).

18. Plug the 23 pin connector (9); with the locking tab

located on top; from the wire harness into the socket
on the controller, push in firmly and make sure that the
locking tab is latched.

19. Check all wires to be sure they are connected to the

proper terminal.

20. Position the Splash Shield under the edge of the seat

opening, install the three christmas tree rivets (4).

21. Reconnect wires to the battery pack.

Replace any

worn or damaged hardware as required.

ITEM

TORQUE SPECIFICATION

44 - 62 in. lbs (5 - 7 Nm)

13 - 15 ft. lbs (18 - 20 Nm)

53 - 71 in. lbs (6 - 8Nm)

Summary of Contents for 611103



























































































































































































Search results

Summary of Contents for 611103

Reviews:

Related manuals for 611103

Brands by name

Popular brands

Ezgo 611103, Service & Repair Manual

Search results

Summary of Contents for 611103

Reviews:

Related manuals for 611103

Brands by name

Popular brands