Ezgo 611103 Service & Repair Manual Download

Page: 80 / 186

Page G-4

MOTOR & MOTOR BRAKE

Repair and Service Manual

Read all of Section B and this section before attempting any procedure. Pay particular attention to all Notices, Cautions and Warnings.

Fig. 7 Motor Brake

DO NOT drop the brake assembly. Dropping or hitting the
brake assembly will damage it.

INSTALLATION

1. Position the brake with the connector at the top as

shown above and install the three hex head bolts (32)
loosely.

2. Connect the wire harness to the motor brake and

move the Run/Tow switch to the ’TOW’ position. This
will provide power to the brake to align the disc mate-
rial.

3. Tighten the three hex head bolts evenly to the speci-

fied torque.

4. Move the Run/Tow switch to the ’RUN’ position.

Replace worn or damaged hardware as required.

ITEM

TORQUE SPECIFICATION

53 - 71 in. lbs (6 - 8 Nm)

Summary of Contents for 611103



























































































































































































Search results

Summary of Contents for 611103

Reviews:

Related manuals for 611103

Brands by name

Popular brands

Ezgo 611103, Service & Repair Manual

Search results

Summary of Contents for 611103

Reviews:

Related manuals for 611103

Brands by name

Popular brands