Ezgo 611103 Service & Repair Manual Download | Manualshive

Page: 158 / 186

background image

Page O-4

TROUBLESHOOTING AND DIAGNOSTICS

Repair and Service Manual

Read all of Section B and this section before attempting any procedure. Pay particular attention to all Notices, Cautions and Warnings.

B

ERROR MESSAGES

1. Current Error Message is displayed on the
ERROR STATUS screen

2. Past 7 Error Codes are displayed on ERROR LOG
screen. The error code along with the run time when
the error occurred

.

WARNING MESSAGES

SETTING TOP SPEED AND PERFORMANCE
PROFILES (read and write)

To change the speed, scroll down the list and highlight
one of the vehicles; Airport, Shuttle or Golf 1, 2, 3 & 4
profiles. After selecting the desired speed press the en-
ter key (button 3) then turn the key switch to ’OFF’, once
the key switch is turned back on the vehicle will display
the new speed setting on the hand held unit.

COURSE ENERGY CONSUMPTION (read
only)

1. Start and Stop the Record Function: display as
’START’, ’STOP’ or ’CLEAR’

2. Scroll down to ’START’ and press the enter key
(button 3) to begin recording the energy consump-
tion.

3. Drive vehicle around the course as it would be
driven during a round of golf.

4. To ’STOP’ the recording make sure that ’STOP’ is
highlighted and press the enter key (button 3). The
energy consumed will be displayed on the screen.

4. Selecting ’CLEAR’ and pressing the enter key
(button 3) will erase all data that is displayed on the
screen.

SERVICE MENU

DIAG REPORT

BATTERY/WARRANTY

WARNINGS

COURSE ENERGY

ERRORS

ERRORS

ERROR LOG

ERROR STATUS

E

E

R

ROR LOG

E

E

R

ROR LOG

CODE LTIME

25107 100.8

25106 91.5

9.1

12833 83.5

SERVICE MENU

WARNINGS

ERRORS

HISTORY
ERROR STATUS

ERROR LOG

STATUS

SETUP PERFORMANCE

GOLF 4 - 14.5

SHUTTLE - 10.5

GOLF 3 - 13.5

AIRPORT - 8.0
GOLF 1 - 11.5

GOLF 2 - 12.5

COURSE ENERGY

KW HRS :

RUNNING TIME :

TOTAL AH :

BATTCHAR :

CLEAR

START

«
...
156
157
158
159
160
...
»

Summary of Contents for 611103



























































































































































































Reviews:

No comments

Related manuals for 611103

Brand: Jacobsen Pages: 64

TOURINO PICK-UP

Brand: Cramer Pages: 16

Trailblazer E2020

Brand: Evinrude Pages: 14

Brand: Panther Pages: 10

Brand: Recon Pages: 102

Brand: Can-Am Pages: 140

Brand: Erde Pages: 8

Brand: Ivarssons i Mestjö Pages: 32

2011 700 Diesel SD

Brand: Arctic Cat Pages: 164

2010 700 Diesel SD

Brand: Arctic Cat Pages: 180

Brand: Yamaha Pages: 92

Brand: Yamaha Pages: 178

Brand: Landa Pages: 38

Brand: Landa Pages: 101

Brand: Yamaha Pages: 320

Brand: Suzuki Pages: 26

GO-4 INTERCEPTOR IV

Brand: Westward Pages: 72

Off-Roader 125-4

Brand: Texas Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands