Ezgo 611103 Service & Repair Manual Download

Page: 59 / 186

ELECTRONIC SPEED CONTROL (AC MOTOR)

Page E-5

Repair and Service Manual

Read all of Section B and this section before attempting any procedure. Pay particular attention to all Notes, Cautions and Warnings.

the back terminal of the solenoid (4) and the white
wire (12) to the resistor, secure in place using a hex
nut (5). Be sure to place larger terminal wires first on
studs with smaller wires on last.

4. Connect the red wire (13) from the positive (+), BL+,

battery terminal and the yellow wire (14) from the wir-
ing harness to the front terminal of the solenoid (4),
secure in place with a hex nut (6). Be sure to place
larger terminal wires first on studs with smaller wires
on last.

Fig. 6 Round Solenoid

5. Reinstall the electronic controller shield as before.
6. Reinstall three christmas tree rivets (1) to secure the

shield to the body and the controller.

7. Connect the negative (-) cable to the battery.

Replace worn or damaged hardware as required.

Controller

Tool List

Qty.

Ratchet ........................................................................ 1
Extension, 3" ............................................................... 1
Extension, 9" ............................................................... 1
Socket, 15 mm ............................................................ 1
Socket, 10 mm ............................................................ 1
Torx Bit, T-27 IP........................................................... 1
Wrench, 10 mm ........................................................... 1

Wrench, 15 mm ...........................................................1
Notched Pry Bar ..........................................................1
Insulated Wrench, 9/16"...............................................1
Pin Punch ....................................................................1
Torque Wrench, in. lbs. ................................................1
Torque Wrench, ft. lbs..................................................1

Using an insulated wrench, disconnect the bat-

tery cable at the negative (-), BL-, battery ter-

minal.
Drain the stored energy from the controller.

Make sure that the Run/Tow switch is in the

Run position, turn the key to reverse and allow

the reverse warning indicator to run down.

The controller is a solid state unit activated by a sole-
noid. The solenoid is hard wired to the electrical harness
and mounted to the controller heat sink. The controller is
located under the seat on the passenger side of the
vehicle. To access the controller, raise and remove the
seat bottom.

1. Disconnect the battery cable at the negative (-), BL-,

battery terminal using an insulated wrench.

2. Drain the stored energy from the controller. Place the

Run/Tow switch in the Run position, turn the key
switch to reverse, wait for the reverse warning indica-
tor to become silent, turn the key switch to the off posi-
tion and remove the key from the switch.

3. Remove three christmas tree rivets (4) securing the

controller splash shield to the rear body and to the
controller heat sink; position splash shield off to one
side to allow access to the controller.

Fig. 7 Controller Splash Shield Cover

4. Disconnect the Red positive (+) battery cable from the

front terminal of the solenoid.

ITEM

TORQUE SPECIFICATION

5, 6

26 - 36 in. lbs (3 - 4 Nm)

44 - 62 in. lbs (5 - 7 Nm)

7 - 13 in. lbs (.75 - 1.5 Nm)

Splash Shield

Failur

e to f

ollo

w these instruc

tions can r

esult in SERIOUS INJUR

Y or DEA

Turn the ignition key to the ‘N’

position and ‘chock’

tires to prevent inadvertent movement.

Turn

the i

gnitio

n ke

y to t

he ‘N

’ pos

ition

and

‘cho

ck’ tir

es to

ent in

adve

rtent

mov

eme

nt.

Remove this plastic cover by removing 3 plastic fasteners. See illustrations below

Rem

ove t

his p

lastic

cove

r by r

emo

ving

3 pla

stic f

aste

ners

. See

illus

tratio

ns b

elow

See emergency brake release instruction under this panel.

See e

merg

ency

brak

e rele

ase in

struc

tion u

nder

this p

anel.

609987

6099

Flip the RUN-T

OW switch to the ‘T

OW’

position and move vehicle to the desired location and

Flip t

he R

UN-T

switc

h to t

he ‘T

’ pos

ition

and

mov

e ve

hicle

to th

e de

sired

loca

tion a

park it properly on level ground and chock tires immediately

park

it pro

perly

on le

vel g

roun

d an

d ch

ock t

ires i

edia

tely.

Turn the ignition key to the ‘OFF’

position, remove key and perform required service

Turn

the i

gnitio

n ke

y to t

he ‘O

FF’ p

ositio

n, re

mov

e ke

y an

d pe

rform

requ

ired s

ervic

procedures following all Safety Guidelines as outlined in your repair manual.

proc

edure

s follo

wing

all S

afety

Guid

eline

s as

outlin

ed in

you

r rep

air m

anua

IF VEHICLE IS INOPERABLE

AND NEEDS T

O BE MOVED:

IF VEH

ICLE IS

INOP

ERAB

LE AN

D NEE

DS TO

BE M

OVED

In Case of T

otal Power Loss and the ‘Run-tow’

Switch DOES NOT Release

In Cas

e of To

tal Po

wer Lo

ss and

the ‘R

un-tow

’ Switc

h DOE

S NOT

Relea

the Brake to Move the V

ehicle :

the Bra

ke to M

ove th

e Vehic

le :

Push center

of fastener

with vehicle

key

depressed

remove.

lift fastener to

When center is

To reuse fastener

push center stem

up then install

fastener

shield into

hole.

through

To secure fastener

in place press

down on

center stem

with head of

fastener

until flush

Summary of Contents for 611103



























































































































































































Search results

Summary of Contents for 611103

Reviews:

Related manuals for 611103

Brands by name

Popular brands

Ezgo 611103, Service & Repair Manual

Search results

Summary of Contents for 611103

Reviews:

Related manuals for 611103

Brands by name

Popular brands