Ezgo 611103 Service & Repair Manual Download Page 111 | Manualshive

Page: 111 / 186

background image

ELECTRICAL COMPONENTS & WIRING

Page K-1

Repair and Service Manual

Read all of Section B and this section before attempting any procedure. Pay particular attention to all Notices, Cautions and Warnings.

B

B

Fig. 1 Main Electrical Harness

MAIN WIRING HARNESS

The Main Electrical Harness for the vehicle is routed
under the floormat, recessed into the floorboard, the for-
ward section runs under the instrument panel into clips
on the front splash shield, the rear section runs under
the rear body and in front of the batteries. The harness
has the Run/Tow switch, the Reverse Warning Indicator
and on early harness the solenoid hard wired into the
main harness. Replacing the Main Wiring Harness.
Tool List................................................................ Qty.
Notched Pry Bar .......................................................... 1
Torx Bit 27 IP ............................................................... 1
Insulated Wrench, 9/16" .............................................. 1

Using an insulated wrench, disconnect the bat-

tery cable at the negative (-), BL-, battery ter-

minal.

To access the main wiring harness for replacement it is
necessary to remove the upper and lower rocker panels,
the floormat, the pedal cover, the front cowl, the top por-
tion of the cup holder and the seat bottom. See the Body
Section in this manual for instructions on removal and
replacement of these items.

1. Disconnect the main wiring harness from the battery

pack using an insulated wrench.

2. Drain the stored energy from the controller. Place the

Run/Tow switch in the ’Run’ position, turn the key
switch to reverse, wait for the reverse warning indica-
tor to become silent then turn the key switch to the off
position and remove it from the switch.

3. Locate the tab under the cowl that extends from the

instrument panel through a slot in the cowl, squeeze
the legs of the tab together and push to the back of
the vehicle while pulling forward on the cowl. Repeat
for the other side —

at this point the cowl is com-

pletely loose

— remove the cowl.

4. Loosen the trim panel (12) by pulling it away from the

MOTOR

DIAGNOSTIC PLUG

INSTRUCMENT
PANEL

WIRING HARNESS

CHARGER RECEPTACLE

BATTERY BANK

«
...
109
110
111
112
113
...
»

Summary of Contents for 611103



























































































































































































Reviews:

No comments

Related manuals for 611103

Brand: Ezgo Pages: 64

Brand: Polaris Pages: 142

TOURINO PICK-UP

Brand: Cramer Pages: 16

Brand: Suzuki Pages: 576

Brand: Primo Water Pages: 12

Brand: Lenoxx Pages: 16

DS Electric 1984

Brand: Club Car Pages: 24

ELECTRIC MINI ATV

Brand: Rider Concept Pages: 29

Brand: Leggero Pages: 98

Minor VM Hydrostatic

Brand: Scarab Pages: 32

Brand: Trail Rover Pages: 38

Brand: GAS GAS Pages: 142

MARSH MASTER 2015

Brand: COAST MACHINERY Pages: 59

SPORTRAX 250X 2009

Brand: Honda Pages: 234

Brand: Yamaha Pages: 1664

Brand: Westbrook Trailers Pages: 24

X20 Convertible Trailer Vac

Brand: Peco Pages: 46

Brand: Rosco Pages: 364

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands