Epson SC-F9300 series User Manual Download Page 100

Page: 100 / 146

Item

Parameter

Explanation

Margin Setting

Side Margin(Right)

3 to 25 mm (5

)

Choose the width of the right margin when media is loaded in the
printer. See the following for more information.

“Printable area” on page 52

Side Margin(Left)

3 to 25 mm (5

)

Choose the width of the left margin when media is loaded in the
printer. See the following for more information.

“Printable area” on page 52

Print Start Position

0 to 800 mm (0

)

Adjust this parameter if you want to print from the near center of the
media or if you want to shift the printed area left from the

Side

Margin(Right)

setting. The area between the right edge of the media

and

Print Start Position

is left blank. If a value is selected for

Side

Margin(Right)

, an additional area corresponding to the width selected

for

Side Margin(Right)

will be left blank. See the following for more

information.

“Printable area” on page 52

Margin Between Pages

Standard

You can adjust a margin between pages. Even after making
adjustments, the size of the margin may change, depending on the
media and usage environment.

The margin increases when the number is moved in the + direction, and
decreases when the number is moved in the - direction.

“Printable area” on page 52

No Margin

-10 mm to +10 mm

Skip Wrinkled Media

Off

is recommended in normal circumstances.

If the print head is scuffed because of wrinkles that occur from media
being left on the heater, set this to

Turn this

to feed media 200 mm and print to avoid wrinkles when

printing with non-continuous jobs. In the following situations, the
media is not fed, even if this is turned

❏

When printing with continuous jobs.

❏

When

Margin Between Pages

is set to

No Margin

Off

Media Check

SC-F9300 Series User's Guide

Using the Control Panel Menu

100

Summary of Contents for SC-F9300 series



















































































































































Search results

Summary of Contents for SC-F9300 series

Reviews:

Related manuals for SC-F9300 series

Brands by name

Popular brands

Epson SC-F9300 series, User Manual

Search results

Summary of Contents for SC-F9300 series

Reviews:

Related manuals for SC-F9300 series

Brands by name

Popular brands