Epson SC-F9300 series User Manual Download Page 64

Page: 64 / 146

Hold the cleaning stick perpendicularly and
wipe the outer areas of all the caps and the
inside of all the guides.

Points to note when cleaning caps

❏

Is there any lint attached to the inside of the
cap?

❏

Is there any lint attached to the flushing pad?

If they are not dirty, cleaning is complete.

“Finishing Cleaning” on page 65

If they require cleaning, see the following
sections and perform the necessary cleaning.

When there is lint or dust in the cap

Remove using the tip of the cleaning stick or tweezers.

If no other parts need to be cleaned, proceed to the
following section.

“Finishing Cleaning” on page 65

When there is lint attached to the
flushing pad

Wipe off lint and dust with the tip of a cleaning stick.

Important:

Do not deform the metal section of the top surface.
If they are deformed, they may damage the print
head.

SC-F9300 Series User's Guide

Maintenance

Summary of Contents for SC-F9300 series



















































































































































Search results

Summary of Contents for SC-F9300 series

Reviews:

Related manuals for SC-F9300 series

Brands by name

Popular brands

Epson SC-F9300 series, User Manual

Search results

Summary of Contents for SC-F9300 series

Reviews:

Related manuals for SC-F9300 series

Brands by name

Popular brands