Epson SC-F9300 series User Manual Download Page 84

Page: 84 / 146

There are two carriage rods, rod A and rod B. Apply
grease to both rods using the grease kit supplied with
the printer.

The grease application tool varies depending on the
rod as shown below.

Carriage rod A

Carriage rod B

Before starting this procedure, be sure to read the
following:

“Precautions regarding maintenance” on page 59

Greasing procedure for carriage
rod A

Buttons that are used in the following settings

After confirming that the printer is ready, press
the

button.

The Maintenance menu will be displayed.

Use the

button to select

Other maintenance

and then press the

button.

Use the

button to select

Grease Carriage

Rod

, and then press the

button.

When

Grease kit is needed. Continue?

displayed. Make sure that you have a grease kit
ready to use.

Select

Yes

, and then press the

button.

Insert the tab of the pad A (new) firmly into the
rectangular slot on the grease tool and fit the
pad to the tool as shown.

Open the front cover.

Hold the pad of the tool firmly against the back
of the carriage rod A, and then slide it smoothly
from the right end to the left end to wipe off
stains on the rod.

Repeat this action four times.

SC-F9300 Series User's Guide

Maintenance

Summary of Contents for SC-F9300 series



















































































































































Search results

Summary of Contents for SC-F9300 series

Reviews:

Related manuals for SC-F9300 series

Brands by name

Popular brands

Epson SC-F9300 series, User Manual

Search results

Summary of Contents for SC-F9300 series

Reviews:

Related manuals for SC-F9300 series

Brands by name

Popular brands