Epson SC-F9300 series User Manual Download Page 73 | Manualshive

Page: 73 / 146

background image

C

In one-second intervals, move the stirring stick
up and down. Repeat about 15 times.

When moving the stirring stick up and down,
touch the ink inlet cap to the ink tank and raise
it until you can see the hook on the stirring
stick completely.

c

Important:

Move the stirring stick slowly. If you move it
too quickly, ink may splatter.

D

Put the ink inlet cap back on the ink tank.

c

Important:

Press the ink inlet cap down firmly so that it
does not detach. If the slider comes into
contact with the ink inlet cap when pulling it
out, the cap could be damaged.

E

Close the ink inlet cover.

Disposing of Waste Ink

Preparing and Replacement
Timing

When Prepare empty waste ink bottle. is displayed,

Prepare a new Waste Ink Bottle as soon as possible.

When you want to replace the Waste Ink Bottle at this
stage due to night operations and so on, select

Replace

Ink Bottle

from the setup menu, and then replace the

bottle. If you perform the replacement without
selecting

Replace Ink Bottle

, the waste ink counter

will not operate correctly.

Maintenance menu

U

“The Maintenance Menu” on

Waste Ink Counter

U

“Waste Ink Counter” on

c

Important:

Never remove the Waste Ink Bottle while printing
or while the heads are being cleaned, unless there
are on-screen instructions. Failure to observe this
precaution could cause ink to leak.

SC-F9300 Series User's Guide

Maintenance

73

«
...
71
72
73
74
75
...
»

Summary of Contents for SC-F9300 series



















































































































































Reviews:

No comments

Related manuals for SC-F9300 series

Brand: Quivogne Pages: 13

Brand: Nel-Tech Labs Pages: 8

Brand: TDR Pages: 8

Brand: VADDIO Pages: 58

Brand: Xaoc Devices Pages: 8

Brand: Yuwell Pages: 2

Brand: Garmin Pages: 2

Brand: Parker Pages: 58

Brand: Martin Pages: 202

Brand: GE Pages: 2

Brand: Ignis Pixel Pages: 4

Deep Root Planter 1.8m

Brand: Zest 4 Leisure Pages: 5

Brand: Faro Pages: 161

Bug Zappers BZ-15

Brand: Black Flag Pages: 2

Brand: Anslut Pages: 20

Brand: Murphy Pages: 20

Brand: REITEL Pages: 20

Brand: Velleman Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands