Epson SC-F9300 series User Manual Download Page 33 | Manualshive

Page: 33 / 146

background image

c

Important:

❏

Do not use the media edge plates with
media that is 0.4 mm or more thick. The
media edge plates could touch and
damage the print head.

❏

Always position the plates so that the
edges of the media are at the centers of
the round holes. Incorrect positioning
causes banding (horizontal banding, tint
unevenness, or stripes) during printing.

❏

Move the media edge plates to the left
and right edges of the platen when they
are not in use.

❏

Do not use the media edge plates if the
sides of the printed media are smudged.

V

Using the Auto Take-up
Reel Unit

The Auto Take-up Reel Unit automatically takes up
media as it is printed, improving the efficiency of
unmanned operation.

The Auto Take-up Reel Unit for this printer can take
up media in either of the following directions.

Printed side in

Printed side out

Taking-up with printed side in places the printed
surface on the inside of the roll. “Printed side in” is
recommended in most situations.

Taking-up with printed side out places the printed
surface on the outside of the roll.

You can check the procedure in a video on YouTube.

Caution:

❏

Follow the instructions in the manual when
loading media or roll cores or removing
media from the take-up roll.
Dropping media, roll cores, or take-up rolls
could result in injury.

❏

Be sure that your hands or hair do not get
caught in the Media Feeding Unit or Auto
Take-up Reel Unit while it is operating.
Failure to observe this precaution could result
in injury.

Important points for correct
take-up

Observe the following points for correct take-up of
media.

❏

We recommend using a take-up roll core with the
same width as the media. If a take-up roll core of
a different width is used, the take-up roll core
may bend, and the media will be taken up
incorrectly.

❏

We recommend “printed side in” for the take-up
of media. “Printed side out” may cause the media
to move around and create a large misalignment
with the roll. When take-up cannot be done
correctly with “printed side out”, do take-up
using “printed side in”.

❏

Media smaller than 36 inches wide may move
around and be taken up incorrectly.

❏

Do not attach take-up roll cores like the ones
shown in the following figure. The take-up
tension will be uneven and the core will spin
loosely. As a result, the paper cannot wind
correctly, which may cause banding in the print
results.

Edges are worn

SC-F9300 Series User's Guide

Basic Operations

33

«
...
31
32
33
34
35
...
»

Summary of Contents for SC-F9300 series



















































































































































Reviews:

No comments

Related manuals for SC-F9300 series

Brand: B&K Pages: 5

Brand: B&K Pages: 28

Brand: XAG Pages: 24

D-MAS HyperSat 2540

Brand: DanMedical Pages: 103

Brand: Gatekeeper Pages: 8

Bure Rise & Go DB 56-309

Brand: Gate Pages: 8

Brand: Rane Pages: 38

Brand: Kartsana Pages: 36

Brand: Octane Fitness Pages: 20

Brand: Oceaneering Pages: 27

Brand: Kärcher Pages: 20

Brand: Parker Research Corp Pages: 3

Brand: Yetter Pages: 24

Brand: Olympus Pages: 130

Brand: Strapack Pages: 16

Brand: Hameg Pages: 60

Brand: Maselec Pages: 6

Firefly Low Voltage Lighting System

Brand: Ultra Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands