Epson SC-F9300 series User Manual Download Page 50

Page: 50 / 146

Head Alignment

Depending on the model or setting status being used,
the maximum length of the media required to print
the test pattern differs as shown below.

Status

Length of Media
Used

In 1 head mode

Approx. 270 mm

In 2 head mode

Approx. 320 mm

Setting procedure

Check that the printer is ready, and load the
media according to the actual usage conditions.

When using the Auto Take-up Reel Unit,
attach the media to the roll core.

“Loading media” on page 27

“Using the Auto Take-up Reel Unit” on

page 33

Press the

Menu

button.

The settings menu will be displayed.

Select

Media Setup

Customize Settings

Media Adjust

Manual

Head Alignment

Press the

button to print the adjustment

pattern.

Wait until printing is complete.

Check the printed adjustment pattern.

Status

Adjustment
Pattern

In 1 head mode

4 blocks, A to D

In 2 head mode

12 blocks, A to L

Select the finest lined pattern (all lines overlap)
for both. Select “-1” in the cases shown below.

The screen for entering values is displayed.

Using the

buttons, enter the pattern

number recorded in Step 5 and press the

button.

When multiple check patterns have been
printed, select the number per check pattern,
and then press the

button.

The media setup menu will be displayed when you
enter the pattern number for the last color.

Changing settings during
printing

Changing the Heater's
Temperature

Buttons that are used in the following settings

Press the

button during printing.

The

Heating & Drying

menu is displayed.

SC-F9300 Series User's Guide

Basic Operations

Summary of Contents for SC-F9300 series



















































































































































Search results

Summary of Contents for SC-F9300 series

Reviews:

Related manuals for SC-F9300 series

Brands by name

Popular brands

Epson SC-F9300 series, User Manual

Search results

Summary of Contents for SC-F9300 series

Reviews:

Related manuals for SC-F9300 series

Brands by name

Popular brands