Epson SC-F9300 series User Manual Download Page 74

Page: 74 / 146

Replace waste ink bottle and press

. is displayed

Replace the Waste Ink Bottle with a new bottle
immediately.

Replacement procedure

“Replacing the Waste Ink

Bottle” on page 74

Waste Ink Counter

The printer uses the waste ink counter to track waste
ink and displays a message when the counter reaches
the warning level.

Replace waste ink bottle and press

and replace the Waste Ink Bottle with a new

one, the counter is cleared automatically.

If you need to replace the waste ink bottle before the
message is displayed, select

Replace Ink Bottle

from

the setup menu.

Maintenance menu

“The Maintenance Menu” on

page 104

Important:

If you replace the Waste Ink Bottle before being
prompted by a message, always clear the waste
ink counter. Otherwise, the replacement interval
for the Waste Ink Bottle will no longer be notified
correctly from the next message.

Replacing the Waste Ink Bottle

Follow the procedure below to replace the parts.

Before starting this procedure, be sure to read the
following:

“Precautions regarding maintenance” on page 59

Remove the Waste Ink Bottle from the Waste
Ink Bottle holder.

If the backside of the stopper is stained, wipe it.

Insert the waste ink tube into the mouth of the
new Waste Ink Bottle and place the Waste Ink
Bottle in the holder.

Tightly seal the lid on the used Waste Ink Bottle.

SC-F9300 Series User's Guide

Maintenance

Summary of Contents for SC-F9300 series



















































































































































Search results

Summary of Contents for SC-F9300 series

Reviews:

Related manuals for SC-F9300 series

Brands by name

Popular brands

Epson SC-F9300 series, User Manual

Search results

Summary of Contents for SC-F9300 series

Reviews:

Related manuals for SC-F9300 series

Brands by name

Popular brands