Epson SC-F9300 series User Manual Download Page 71 | Manualshive

Page: 71 / 146

background image

Ink other than High Density Black Ink

High Density Black Ink

c

Important:

Press the ink inlet cap down firmly so that it
does not detach. If the slider comes into
contact with the ink inlet cap when pulling it
out, the cap could be damaged.

M

Close the slider ink inlet cover.

When ink adheres to the heat shield when
refilling the ink, remove the heat shield and
clean it.

U

“Cleaning the Heat Shield” on page 83

Procedure for stirring the
High Density Black Ink

A characteristic of High Density Black Ink is that
sedimentation occurs easily. Stir the ink in the ink
tank once a week. There may be color differences in
the printouts if printing is performed when
sedimentation has occurred.

You can stir the ink whenever you want, regardless if
you are printing or if the printer is on or off.

Before starting this procedure, be sure to read the
following:

U

“Precautions regarding maintenance” on page 59

SC-F9300 Series User's Guide

Maintenance

71

«
...
69
70
71
72
73
...
»

Summary of Contents for SC-F9300 series



















































































































































Reviews:

No comments

Related manuals for SC-F9300 series

Brand: Olympus Pages: 86

Giraffe OmniBed

Brand: Ohmeda Pages: 54

Brand: YSI Pages: 70

Brand: jcb Pages: 41

Brand: 4iiii Pages: 36

Brand: 4iiii Pages: 34

Brand: 4EVAC Pages: 27

Brand: Hakko Electronics Pages: 8

Professional HS 8

Brand: Hailo Pages: 5

Brand: Hainbuch Pages: 52

Brand: Ognibene Pages: 28

Brand: Hameg Pages: 24

Brand: Vaisala Pages: 118

Brand: RAPID REBOOT Pages: 18

Brand: MacDon Pages: 170

Brand: MacDon Pages: 108

Brand: MacDon Pages: 108

Brand: MacDon Pages: 51

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands