Epson SC-F9300 series User Manual Download Page 8

Page: 8 / 146

Airflow vents

Allows air to flow into the printer. Do not obstruct these vents.

Waste ink tube

Tubes for ejecting waste ink. Be sure the end of this tube is in the Waste Ink Bottle while the printer is in use.

Stopper

This prevents splatter when discharging waste ink.

Print with the opening of the Waste Ink Bottle sealed, except when replacing the Waste Ink Bottle.

Waste Ink Bottle

Waste ink collects in this bottle.

Replace it with a new Waste Ink Bottle when a message is displayed on the control panel prompting you to do
so.

“Disposing of Waste Ink” on page 73

Casters

There are two casters on each leg. Once installation is complete, the front casters should be kept locked while
the printer is in use.

Adjusters

When installing on a carpeted floor or a sloping floor, check level gauge of the printer and adjust these to keep
the printer stable.

Setup Guide

AC inlet #1/AC inlet #2

Connects the power cable. Be sure to connect both cables.

LAN port

Connects the LAN cable. Use a shielded twisted pair cable (category 5e or higher).

Data lamp

The data lamp lights or flashes to indicate the network connection status and whether the printer is receiving
data.

: Connected.

Flashing

: Connected. Receiving data.

SC-F9300 Series User's Guide

Introduction

Summary of Contents for SC-F9300 series



















































































































































Search results

Summary of Contents for SC-F9300 series

Reviews:

Related manuals for SC-F9300 series

Brands by name

Popular brands

Epson SC-F9300 series, User Manual

Search results

Summary of Contents for SC-F9300 series

Reviews:

Related manuals for SC-F9300 series

Brands by name

Popular brands