Epson SC-F9300 series User Manual Download Page 133

Page: 133 / 146

Ink Specifications

Type

Dedicated ink pack

Sublimation dye
ink

High Density Black, Cyan,
Magenta, Yellow

Use by date

Date printed on the ink pack
(stored at normal temperatures)

Print quality
guarantee expiry

25 days (from the day the ink tank
was refilled with an ink pack)

Storage
temperature

5 to 35 °C

Capacity

1000 ml

Note:

To ensure the colors you want to print, maintain a
constant room temperature of 15 to 25 °C.

Information of EU declaration of conformity

The full text of the EU declaration of conformity of
this equipment is available at the following internet
address.

http://www.epson.eu/conformity

SC-F9300 Series User's Guide

Appendix

133

Summary of Contents for SC-F9300 series



















































































































































Search results

Summary of Contents for SC-F9300 series

Reviews:

Related manuals for SC-F9300 series

Brands by name

Popular brands

Epson SC-F9300 series, User Manual

Search results

Summary of Contents for SC-F9300 series

Reviews:

Related manuals for SC-F9300 series

Brands by name

Popular brands