Epson SC-F9300 series User Manual Download Page 54

Page: 54 / 146

By selecting

No Margin

Margin Between Pages

in the settings menu for the printer, you can adjust the

margins in a range between -10 mm and +10 mm.

This may be available in the RIP depending on the RIP software being used. Contact the RIP manufacturer
for more information.

Note the following points when setting margins.

❏

Leave margins of 10 mm or more when using media edge plates. Narrower margins could result in printer printing
over the plates.

❏

If the total of the print data width and set left and right margins exceeds the printable area, a portion of the data will
not be printed.

Note:

If the following points are not observed when Media Size Check is

Off

, printing may occur outside the left and right

edges of the media. Ink used outside the edges of the media will stain the inside of the printer.

❏

Ensure that the print data width does not exceed the loaded media width.

❏

When media is loaded to the left of the right side reference position, align the

Print Start Position

setting with the

position where the media set.

“The Printer Setup Menu” on page 99

SC-F9300 Series User's Guide

Basic Operations

Summary of Contents for SC-F9300 series



















































































































































Search results

Summary of Contents for SC-F9300 series

Reviews:

Related manuals for SC-F9300 series

Brands by name

Popular brands

Epson SC-F9300 series, User Manual

Search results

Summary of Contents for SC-F9300 series

Reviews:

Related manuals for SC-F9300 series

Brands by name

Popular brands