Epson SC-F9300 series User Manual Download Page 76

Page: 76 / 146

Important:

About the Head Cleaning Set Counter

The printer tracks amounts consumed using the
head cleaning set counter and displays a message
when the counter reaches the warning level.

If you replace parts when the message “

Head

Cleaning Set Life

” is displayed, the counter is

cleared automatically.

If you need to replace the parts before the message
is displayed, implement

Head Cleaning Set

from

the setup menu.

Maintenance menu

“The Maintenance

Menu” on page 104

When

Head Cleaning Set Life is displayed

See the following page, and replace all the parts
included in the head cleaning set. Printing cannot be
performed if the parts are not replaced.

The head cleaning sets contains the following parts.

❏

Wiper unit (x1)

❏

Flushing pad (x1)

❏

Gloves (x2)

Always choose a replacement head cleaning set that is
specified for this printer.

“Options and Consumable Products” on

page 117

Before starting this procedure, be sure to read the
following:

“Precautions regarding maintenance” on page 59

How to Replace the Head
Cleaning Set

Press the

button in the

Head Cleaning

Set Life

screen.

A confirmation message appears twice.

Thoroughly confirm the content on each
screen, and then click the

button.

After the print head moves to the left end of the
printer, open the right maintenance cover.

Place your fingers in the groove on the back of
the wiper unit, and tilt it forward a little.

Grip the sides, and pull it straight up to lift it out.

SC-F9300 Series User's Guide

Maintenance

Summary of Contents for SC-F9300 series



















































































































































Search results

Summary of Contents for SC-F9300 series

Reviews:

Related manuals for SC-F9300 series

Brands by name

Popular brands

Epson SC-F9300 series, User Manual

Search results

Summary of Contents for SC-F9300 series

Reviews:

Related manuals for SC-F9300 series

Brands by name

Popular brands