Epson SC-F9300 series User Manual Download Page 51

Page: 51 / 146

Press the

buttons to select

Heater

Temperature

, and then press the

button.

Choose a value.

Press the

buttons to set the temperature.

When you press the

button, the settings for

the currently selected media are updated, and
the Heating & Drying menu is displayed.

When you press the

button, the menu is

closed and the status display screen is displayed.

Note:

The time needed for the heaters to reach the
specified temperatures varies with the ambient
temperature.

Correcting Banding

When you want to correct banding during printing,
perform Feed Adjustment.

Buttons that are used in the following settings

Press the

button during printing.

The current adjustment value is displayed.

Use the

buttons to change the current value.

If the feed amount is too small, black bands
(dark stripes) will appear; adjust the feed
amount upwards.

If, in contrast, the feed amount is too large,
white bands (pale stripes) will appear; adjust
the feed amount downwards.

Check the printing result. If you are not
satisfied with the results, use the

buttons

to change the value.

This updates the setting value of

Feed

Adjustment

in the currently selected media

settings.

Press the

button to display the status

display screen.

Note:

If the setting is changed, the icon is displayed on
the control panel screen as shown below. To clear
this icon, carry out the following operations.

❏

Restart

Feed Adjustment

❏

Execute

Restore Settings

SC-F9300 Series User's Guide

Basic Operations

Summary of Contents for SC-F9300 series



















































































































































Search results

Summary of Contents for SC-F9300 series

Reviews:

Related manuals for SC-F9300 series

Brands by name

Popular brands

Epson SC-F9300 series, User Manual

Search results

Summary of Contents for SC-F9300 series

Reviews:

Related manuals for SC-F9300 series

Brands by name

Popular brands