Epson SC-F9300 series User Manual Download Page 83

Page: 83 / 146

Cleaning the Heat Shield

When it becomes hard to see inside the ink tank
because ink has adhered to the heat shield, remove the
heat shield and clean it.

A Philips head screwdriver is required for the
following work. Make sure to have one prepared
before you start working.

Before starting this procedure, be sure to read the
following:

“Precautions regarding maintenance” on page 59

Remove the heat shield.

Completely loosen the four screws that hold the
heat shield in place to remove the heat shield.

Soak a soft cloth in water, wring it out
thoroughly, and then wipe off any ink that has
adhered to the heat shield.

Install the heat shield.

Align the heat shield's holes with those in the
ink tank holder and tightly screw in the screws.

Applying Grease to the
Carriage Rod

When

Apply secondary carriage rod grease. See

manual.

is displayed on the control panel screen,

follow the steps below to apply grease to the carriage
rod as soon as possible.

Location of Carriage Rod and
Used Pad

SC-F9300 Series User's Guide

Maintenance

Summary of Contents for SC-F9300 series



















































































































































Search results

Summary of Contents for SC-F9300 series

Reviews:

Related manuals for SC-F9300 series

Brands by name

Popular brands

Epson SC-F9300 series, User Manual

Search results

Summary of Contents for SC-F9300 series

Reviews:

Related manuals for SC-F9300 series

Brands by name

Popular brands