Epson SC-F9300 series User Manual Download Page 52

Page: 52 / 146

Printable area

The left and right edges of media recognized by the printer varies as shown below according to the Media
Size Check settings.

Media Size Check

: The printer automatically detects the left and right edges of the loaded media.

When media edge plates are attached, within 5 mm of the left and right edges of the
media is recognized as the media edge.

The edges of the media are not detected correctly if the media edge plates are not
attached correctly.

“Loading media” on page 27

Media Size Check

Off

: The center of the black rectangle on the heater's label (shown in the illustration below) is

the standard position for the right edge of the media. Regardless of the width of the
loaded media, the left edge of the media is determined to be 1,626 mm (64 inches) from
the standard position for the right edge.

SC-F9300 Series User's Guide

Basic Operations

Summary of Contents for SC-F9300 series



















































































































































Search results

Summary of Contents for SC-F9300 series

Reviews:

Related manuals for SC-F9300 series

Brands by name

Popular brands

Epson SC-F9300 series, User Manual

Search results

Summary of Contents for SC-F9300 series

Reviews:

Related manuals for SC-F9300 series

Brands by name

Popular brands