Emerson Rosemount Oxymitter DR Reference Manual Download Page 40

Page: 40 / 98

a) Connect the oxygen signal lines from the signal conditioning electronics to

the terminals shown in

Figure 2-14

b) Connect the Type K thermocouple lines from the signal conditioning

electronics to the terminals indicated in

Figure 2-14

4. Install terminal cover (20,

Figure 2-13

) and secure with cover lock (27), gasket (26),

and screw (25).

2.3

Pneumatic installation

If instrument air will be used as reference air, connect the reference air set to the
transmitter.

CAUTION

Damage can result from having a cold transmitter exposed to the process gases.

Upon completing installation, make sure the transmitter is turned on and operating before
firing up the combustion process.

CAUTION

Thermal cycling can cause condensation and premature aging.

During outages, if possible, leave all transmitter units running.

CAUTION

If washing down the ducts during outage, make sure to power down the transmitter units
and remove them from the wash area.

See

System considerations

. Install the reference air set in accordance with

Figure 2-15

Install

Reference Manual

October 2019

00809-0100-4880

Emerson.com/Rosemount

Summary of Contents for Rosemount Oxymitter DR



































































































Search results

Summary of Contents for Rosemount Oxymitter DR

Reviews:

Related manuals for Rosemount Oxymitter DR

Brands by name

Popular brands

Emerson Rosemount Oxymitter DR, Reference Manual

Search results

Summary of Contents for Rosemount Oxymitter DR

Reviews:

Related manuals for Rosemount Oxymitter DR

Brands by name

Popular brands