manualshive.com logo in svg

Emerson Rosemount Oxymitter DR, Reference Manual

Share
Download
Emerson Rosemount Oxymitter DR Reference Manual Download Page 47

4. Replace with new EPROM.
5. Close electronics enclosure and power up system.

2.4.5

Set up World Class 3000 intelligent field transmitter

The Rosemount

™

 Oxymitter DR probe operates with a 115 Vac heater. Ensure that the

voltage selection jumpers in the IFT or HPS, if used, are set properly.

IFT 3000 power supply board jumper configuration

 WARNING

Always disconnect line voltage from intelligent field transmitter before changing jumpers.

Line voltage selection

Jumper (install)

100 Vac

JM3, JM7, JM2

120 Vac

JM8, JM7, JM1

220 Vac

JM6, JM5, JM2

240 Vac

JM6, JM5, JM1

Probe heater voltage selection

Jumper (install)

World Class probe (44 V)

JM10

218 probe (115 V)

JM9

World Class Direct Replacement probe (115 V)
or Rosemount Oxymitter Direct Replacement
probe (115 V)

JM9

 CAUTION

If incorrect heater voltage is selected, damage to the probe may occur.

Always update the relevant labeling to reflect the select voltage.

Heater power supply (HPS 3000) jumper configuration

 WARNING

Always disconnect line voltage from heater power supply and analog electronics (if used)
before changing jumpers.

Line voltage selection

Jumper (install)

100/120 Vac

(1)

JM4, JM1

220/240 Vac

JM5

(1)

100 Vac operation requires transformer part number 1M03961G02.

Reference Manual

Install

00809-0100-4880

October 2019

Rosemount Oxymitter DR

47

Summary of Contents for Rosemount Oxymitter DR



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands