manualshive.com logo in svg

Emerson Rosemount Oxymitter DR, Reference Manual

Share
Download
Emerson Rosemount Oxymitter DR Reference Manual Download Page 67

5

Troubleshoot

 WARNING

Failure to install covers and ground leads could result in serious injury or death.

Install all protective equipment covers and safety ground leads after troubleshooting.

5.1

No response to oxygen concentration change
when heater is cold and thermocouple mV
output is less than setpoint

Potential cause

Thermocouple failure

Recommended actions

1. Check thermcouple continuity.
2. Replace thermocouple or return probe to Rosemount

™

.

Potential cause

Heater failure

Recommended actions

1. Check heater cold resistance.

It should be 67 to 77 ohm.

2. Replace heater or return to Rosemount.

Potential cause

Electronics failure

Recommended actions

1. Triac O/P to heater.
2. Check electronics package.

5.2

No response to oxygen concentration change
when heater is hot and thermocouple mV
output is at setpoint ±0.2 mV

Potential cause

Recorder failure

Reference Manual

Troubleshoot

00809-0100-4880

October 2019

Rosemount Oxymitter DR

67

Summary of Contents for Rosemount Oxymitter DR



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands