manualshive.com logo in svg

Emerson Rosemount Oxymitter DR, Reference Manual

Share
Download
Emerson Rosemount Oxymitter DR Reference Manual Download Page 53

4

Maintenance and service

4.1

Overview

This section identifies the calibration methods available and provides the procedures to
maintain and service the transmitter.

 WARNING

When working on the laboratory bench, be aware that the transmitter, probe tube, and
flame arrestor hub can be hot (up to 572 °F [300 °C]) in the region of the probe heater.

 WARNING

Failure to install covers and ground leads could result in serious injury or death.

Install all protective equipment covers and safety ground leads after installation.

4.2

Calibrate

Calibrate the Rosemount

™

 Oxymitter DR when you commission it.

 WARNING

The probe may be hot and may cause severe burns.

Remove the probe from the stack for all service activities. Allow the unit to cool and take it
to a clean work area.

 WARNING

There is voltage up to 115 Vac.

Disconnect and lock out power before working on any electrical components.

Under normal circumstances, the probe will not require frequent calibration. When
calibration is required, follow the procedure in the Reference Manual applicable to your
electronics package. Use 

Calibration record

 to track probe performance.

Reference Manual

Maintenance and service

00809-0100-4880

October 2019

Rosemount Oxymitter DR

53

Summary of Contents for Rosemount Oxymitter DR



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands