manualshive.com logo in svg

Emerson Rosemount Oxymitter DR, Reference Manual

Share
Download
Emerson Rosemount Oxymitter DR Reference Manual Download Page 71

Figure 5-1: Probe Leakage Paths, Bottom View

A. Corrugated seal

B. Reference air exhaust port

C. Probe head

D. Probe flange gasket

The sensing cell is bolted to the end of the probe and uses a corrugated metallic seal
(Item 25, 

Figure 1

).

3. This seal can only be used one time, so always replace this seal when replacing a

cell. Always apply anti-seize compound on both sides of the corrugations.

5.7

Probe passes calibration, but still appears to
read too low

Potential cause

The diffusion element at the end of the probe is a passive filter. It plugs very slowly since
there is no active flow being drawn across it. In applications that have a heavy particulate
loading (coal or wood fired boilers, cement and lime kilns, catalyst regeneration, recover
boilers, etc.) the diffusion element will eventually plug. This may cause a calibration shift.

Recommended actions

1. Do not pressurize the sensing cell during calibrations by flowing excessive cal gas

against a plugged diffuser.

2. Only set calibration flow rates when a new diffuser is installed.
3. As the diffuser plugs, do not adjust the flow rates upward.

Reference Manual

Troubleshoot

00809-0100-4880

October 2019

Rosemount Oxymitter DR

71

Summary of Contents for Rosemount Oxymitter DR



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands