manualshive.com logo in svg

Emerson Rosemount Oxymitter DR, Reference Manual

Share
Download
Emerson Rosemount Oxymitter DR Reference Manual Download Page 43

Figure 2-16: Temperature Controller Card Calibration Points

3. Set voltmeter to read DC millivolts (mV).
4. Attach voltmeter with positive (+) lead on TP1 and negative (-) on either Pin 2 or 7.

Note

The voltage given above is for an ambient (machinery space) temperature of 77 °F
(25 °C). For each degree of ambient temperature above or below 77 °F (25 °C), add
or subract 0.242 mV from the nominal. Example: AT 87 °F (31 °C), the nominal
voltage of -322.3 mV should be increased (made less negative) by 10 x 0.242 or
2.42 mV, making the adjusted nominal -319.9 mV.

5. Adjust potentiometer M110-1 to read 322.3 millivolts nominal.
6. Remove voltmeter leads.
7. Remove jumper wire.

2.4.2

Set up Westinghouse Model 218A electronics

Before beginning operation, it is important to change the probe heater setpoint of the
existing electronics to support the Rosemount

™

 Oxymitter DR probe. To convert the

Reference Manual

Install

00809-0100-4880

October 2019

Rosemount Oxymitter DR

43

Summary of Contents for Rosemount Oxymitter DR



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands