Emerson Rosemount Oxymitter DR Reference Manual Download Page 92 | Manualshive

Page: 92 / 98

background image

Oxymitter oxygen transmitters (Integral & DR): OXT4C, OXT4CNF, OXT4CDR, and
OXT4CDRNF

Class I, Division 1, Groups B, C, and D

Class I, Zone 1, Ex d IIB+H2 T2

Class I, Zone 1, AEx d IIB+H2 T2

Oxymitter oxygen transmitters (split achitecture, probe with remote electronics): OXT4C,
OXT4CNF, 6A00094G

Class I, Zone 1, Ex de IIB+H2 T6 (remote electronics) / T2 probe)

Class I, Zone 1, AEx de IIB+H2 T6 (remote electronics) / (T2 (probe)

Class 1, Division 1, Groups B, C, and D T2 (probe)

Class 1, Division 2, Groups B, C and D T6 (remote electronics)

Special Conditions for Safe Use:

1. Non-flame arrestor probe -"NF" versions must have the probe installed in a non-

classified area.

2. When the probe tube is mounted in a hazardous (classified) area (with flame

arrestor end to complete the assembly) calibration lines that travel in and out of the
equipment bringing reference gas must not contain a pressure higher than 1.1
times the atmospheric pressure; these calibration lines shall not contain pure
oxygen, acetylene, or combustible gases other than the gases for which this Zone 1
classified application has been investigated for: Group IIB +H2 gases.

3. There are no interchangeable components.

4. Contact the original manufacturer for information of flameproof joint dimensions.

5. Fastener property class must be A2-70 for units intended for use in Zone 1 classified

areas.

6. Any other electronics not covered by this report and used in conjunction with the

Rosemount

™

Oxymitter probes or with the remote electronics must be installed in a

non-classified area (ex. Rosemount Xi Advanced Electronics).

(1)

Except Temperature Code T1 for 44V

∼

model of Rosemount OXT4CDR only.

Rosemount

™

Oxymitter

™

product certifications

Reference Manual

October 2019

00809-0100-4880

92

Emerson.com/Rosemount

«
...
90
91
92
93
94
...
»

Summary of Contents for Rosemount Oxymitter DR



































































































Reviews:

No comments

Related manuals for Rosemount Oxymitter DR

Brand: VELOCICALC Pages: 6

Brand: Panametrics Pages: 68

Brand: Ulvac Pages: 24

Brand: TC Electronic Pages: 20

FLEXFLO M4 Series

Brand: Blue-White Pages: 64

Brand: Kipp & Zonen Pages: 32

Brand: Interacoustics Pages: 54

Brand: PCB Piezotronics Pages: 10

WD-35606-00, WD-35606-05

Brand: Oakton Pages: 10

Brand: Fuji Electric Pages: 85

Brand: Tektronix Pages: 116

Brand: Omega Pages: 22

Brand: Stabila Pages: 14

Brand: envea Pages: 68

Brand: Prosense Pages: 35

Brand: Rohde & Schwarz Pages: 46

Dimension Master Plus

Brand: Calculated Industries Pages: 40

Brand: Velleman Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands