Emerson Rosemount Oxymitter DR Reference Manual Download Page 24

Page: 24 / 98

Figure 2-1: Rosemount

™

Oxymitter 4000 Probe Installation

Note

These flat faced flanges are measured to ANSI and DIN patterns and are not pressure
rated. All dimensions are in millimeters with inches in parentheses unless otherwise noted.

A. Dimension A.

B. Dimension B.

C. 0.062-in. (1,57 mm) gasket.

D. Insulate if exposed to ambient weather conditions.

E. Certification approved label.
F. External earth.

G. Internal earth.
H. Electrical connection

NPT.

I. See

Table 2-1

J. Cover removal and access.

K. Bottom view.

L. Vent reference air.

M. See

Table 2-2

Table 2-1: Calibration Gas and Reference Air

Calibration gas

Reference air

ANSI

6.34 (

) tube

DIN

6.35 (

) tube

Table 2-2: Mounting Flange (Gasket Included)

ANSI

DIN

Flange diameter

190 (7.5)

210 (8.25)

Install

Reference Manual

October 2019

00809-0100-4880

Emerson.com/Rosemount

Summary of Contents for Rosemount Oxymitter DR



































































































Search results

Summary of Contents for Rosemount Oxymitter DR

Reviews:

Related manuals for Rosemount Oxymitter DR

Brands by name

Popular brands

Emerson Rosemount Oxymitter DR, Reference Manual

Search results

Summary of Contents for Rosemount Oxymitter DR

Reviews:

Related manuals for Rosemount Oxymitter DR

Brands by name

Popular brands