manualshive.com logo in svg

Emerson Rosemount Oxymitter DR, Reference Manual

Share
Download
Emerson Rosemount Oxymitter DR Reference Manual Download Page 19

Cup type diffusion assembly

Use the cup type diffusion assembly in high temperature applications where frequent
diffusion element plugging is an option.

Figure 1-5: Cup Type Diffusion Assembly

The assembly is available with either a 5 micron or 40 micron sintered Hastelloy element.
This diffusion element offers the greater surface area of the ceramic element, but is much
more rugged. This element is also available with a dust seal for use with an abrasive shield.

Abrasive shield assembly

The abrasive shield assembly is a stainless steel tube that surrounds the probe assembly.
The shield protects against particle abrasion and condensations, provides a guide for ease
of insertion, and acts as a positive support, especially for longer probes. The abrasive
shield assembly uses a modified diffusor and vee deflector assembly, fitted with dual dust
seal packing.

Reference Manual

Description and specifications

00809-0100-4880

October 2019

Rosemount Oxymitter DR

19

Summary of Contents for Rosemount Oxymitter DR



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands